Saturday, May 30, 2015

Industrial Engineering of Flow Production Lines - Thought Before Taiichi Ohno and Shigeo Shingo


Japanese were rational shoppers for production technology and management methods from USA and other countries. Taiichi Ohno and Shigeo Shingo combination improved the production line technique pioneered by Henry Ford in to a very high productive system. There is a book written during Henry Ford's time itself describing the full process of Ford system (Hartley W. Barclay  "Ford Production Methods," Harper & Brothers, New York, 1936.). MIT faculty, Richard Muther published a book in 1944 describing the planning, optimizing, and operating the production line system. He also wrote essays in Maynard's Handbook on Industrial Engineering on the topic.

We can see that quality and maintenance were given stress by Muther. Ohno and Shingo developed methods and tools to squeeze out further waste from the production line system due to extra setup time, poor quality and maintenance problems.

Muther's Description



Line production is a method of manufacture or an arrangement of work areas where the material moves continuously and at a uniform rate through a sequence of balanced operations which permit of simultaneous performance throughout, the work progressing toward completion along a reasonably direct path. Actually, the complete refinements of line production are seldom attained.

Principles of Production Flow Line



1. The principle of minimum distance moved.
2. The principle of flow of work.
3. The principle of division of labor
4. The principle of simultation or simultaneous operation
5. The principle of unit operation
6. The principle of fixed routing
7. The principle of minimum time or material in process
8. The principle of interachangeability



Enforcement of Operation Study.


Muther gives this point as an advantage of Production Flow Line.

It is especially important that adequate operation-analysis and methods study go into the job before it starts into production.

When a production line is installed, it works as a unit. Recognition of this necessity causes a critical examination of every phase of the job. This demand for thorough analysis of all details leads to many improvements in operations which might otherwise never have been noticed. Thus efficient  performance of the work follows.




Line production and  the motion study




In line production the work of motion study should be conducted along with the design of the tools. The chief objective is to build the quality and cost of the job and the skill required into the tools. The ease of operation is  highly desirable. Thought should be given to the motions of the operator of the tool before it goes into the line. Building the line as a piecemeal activity with work simplification
appearing after the job is under way is not only wasteful, but it leads to unbalancing the line


Motion economy rules to guide tool designers and process men.


1. Make the necessary movements as short as possible without crowding the operator.
2. Replace hand movement by automatic machine movement where practical.
3. Replace hand movement by foot movement.
4. Eliminate the passing of work from one hand to the other.
5. Provide hand levers, etc., with multiple functions.
6. Use mechanical ejectors.
7. Arrange so that finished work will drop from fixture into discharge chutes. Use drop discharge chutes and the pushthrough idea.
8. When drop discharge cannot be used, arrangement for disposal directly in front of operator, over top of machine, is often a good solution.
9. Arrange for getting new work from hopper or chute as close as possible to loading point or from location close to discharge point so as to overlap movements.
10. Provide mechanical holders to eliminate the use of the operator's hand as a holding device.
11. When possible keep hand movements within radius of forearm pivoted from elbow. In all events keep within radius of full arm without body bend or twist and without necessity for stepping to reach point desired.
12. Eliminate barriers so that movements can follow shortest path.
13. Keep both hands busy with useful work and avoid waiting of one hand.
14. Provide double station fixtures; one for each hand.
15. Centralize all control levers and starting buttons within the normal work area.
16. Aid locating by means of slides, guides, flanges, stops, bell mouth holes and bullet-nosed pins.
17. Separate scrap from good parts by simple mechanical means.
18. Eliminate all unnecessary use of the eyes. Keep necessary eye use within small space (about six-inch circle if possible).
19. Avoid necessity for operator to assume uncomfortable position. Most of the work should be at elbow level when seated and 6" below elbow level when standing.
20. Build controls of proper size, shape, and weight, and build to operate without undue effort.




Perquisites for Feasibility for Establishing Production Flow Line


1. Quantity
2. Balance
3. Continuity


Methods and Equipment



It is especially important that adequate operation-analysis and methods study go into the job before it starts into production.

Also it is adequate many times to supply a line with equipment that is slower instead of the fastest one available in the market.  The machine must serve the needs of the line speed to do its role in the line.



Line Balance


The desired rate of production is converted into a time for work station. This time is called station time or cycle time. If every operator and every equipment is busy for this cycle time,the line has perfect balance. But this perfect balance is rarely achieved. Operators with idle time can be assigned material handling, taking routine care of the machine etc.




Mechanics of Balancing

Adjust operations by combining or dividing operations to get a total time that is equal to the station time.


Layout


Make sure:

1. adequate space for maintenance and repair.
2. space for material handling
3. adequate storage space for materials
4. provision of inspection points

Manning the Line


The number of operators required equals the total time (in standard hours allowed) required to perform all operations on one unit mutliplied by the rate of production scheduled divided by the length of the shift or period worked in hours per man. This number is based on no idle time to balance.


Assuring Continuity of Manpower


If a line has to work all operators have to be on the line as per planned. No doubt line can be operated at lower rates of output with lesser number of operators. But this is once again planned before hand. Hence the number of operators has to be assessed before the start of the line and actions are to be taken to see that planned number of operators are there.


Incentives


Some companies give incentives and operators as a group have to the freedom to operate the line at the speed they desire and also vary it as they want.


Assuring Continuity of Material


To keep a line running, adequate materials and components must flow into the line at various work stations as per plan. Quantity, quality and location have to right. Material and component planning must synchronize and schedule the work so that everything flows together as needed.

To assure the material,  advance plans are required and these plans are refined as actual production period approaches.  Muther described that a company makes five different types of plans.

1. Broad plan for the year.
2. Tentative 90-day schedule
3. Definite program for 30 days
4. Shipping schedules for 10 days
5. Daily schedule with complete specificationi



Purchasing


In line production, the ability of the vendor to supply the correct parts when they are needed is very important.  The supplier has to be reliable in both quantity and quality.

Material Control


Storage of material along the line

1. Store material at the point of use.
2. Predetermine and identify all storage places along the line.
3. Replenish material along line every night.
4. Have adequate communication system for material control men.
5. Make material control people conscious of not wasting material and components due to faulty handling.


Quality


Muther has listed the factors that may aid quality in line production. Similarly he highlighted some factors that give rise to quality problems.

He gave the following directions to improve quality.

1. Test all sample parts for quality check.
2. Check all tools, dies, and fixtures to make sure that they produce quality output.
3. In stead of depending on individuals, put confidence in  tooling, inspection gauges, and fixtures (This point needs thinking. Is Muther hinting at Poka Yoke?)
4. Plan for the inspection group to be busier than usual during pilot-lot or trial run period.
5. Assign inspectors along the line:
6. Maintain clean-up touch up stations at the end of the line to care for minor defects.
7. Stop production line and move operators to the end of the line to correct units when large number of mistakes occur.


Maintenance


Machines should not break down during the time line is running. All maintenance activities have to be undertaken to ensure that all machines are available during the planned run of time of line.

The recommended steps:

1. Sound preventive maintenance program involving periodic inspectioni, repair, or  replacement of tools, equipment, and handling devices.
2. Rapid communication system or automatic signaling devices to indicate a breakdown and where it has occurred.
3. Ample use of fuses, overload switches, shear pin on conveyor drives, electric-cye or limit switch controls to stop overrunning.
4. Pay group incentive based on freedom from downtime on the line.
5. Stand-by equipment
6. Guards and protective devices to avoid machine or conveyor jamming.





Saturday, May 23, 2015

Chapter - Assembly Line or System Balancing - 2015 Edition



Bibliography

2013

Assembly Line Balancing: A Review of Developments and
Trends in Approach to Industrial Application
By Naveen Kumar & Dalgobind Mahto
Green Hills Engineering College
Global Journal of Researches in Engineering
Industrial Engineering
Volume 13 Issue 2 Version 1.0 Year 2013
Type: Double Blind Peer Reviewed International Research Journal
Publisher: Global Journals Inc. (USA)
https://globaljournals.org/GJRE_Volume13/4-Assembly-Line-Balancing-A-Review-of.pdf

A good research review of 100 papers up to 2012. Needs to be read

2012


Balancing Mixed Model Assembly Lines in an Automobile Seat Plan - Masters Thesis
http://www.fbe.deu.edu.tr/ALL_FILES/Tez_Arsivi/2012/yl_t3073.pdf

Software for assembly line balancing
http://www.vsrdjournals.com/ME/Issue/2012_04_Apr/Web/3_Abhishek_Dwivedi_639_Research_Article_ME_Apr_2012.pdf

2011
Mixed-model assembly line at Volvo Construction
Equipment
Requirements for mixed-model assembly line at Volvo Construction
Equipment and a case study at the Arvika plant
Master of Science Thesis in Production Engineering
2011
http://publications.lib.chalmers.se/records/fulltext/151274.pdf


2010
P. Chutima and P. Olanviwatchai, "Mixed-Model U-Shaped Assembly Line Balancing Problems with Coincidence Memetic Algorithm," Journal of Software Engineering and Applications, Vol. 3 No. 4, 2010, pp. 347-363. doi: 10.4236/jsea.2010.34040.
http://www.scirp.org/Journal/PaperInformation.aspx?PaperID=1694#.VV4oGLmqqko



Supply Chain Engineering: Useful Methods and Techniques
Alexandre Dolgui, Jean-Marie Proth
Springer Science & Business Media, Jun 2, 2010 - 541 pages
The book contain 2 to 3 very good chapters on line balancing
https://books.google.co.in/books?id=A8QzC6wE-KsC


2008
Simple and U-type assembly line balancing problems with a learning effect
M. Duran Toksarıa, , , Selçuk K. İşleyenb, Ertan Günerc, Ömer Faruk Baykoçc
Applied Mathematical Modelling
Volume 32, Issue 12, December 2008, Pages 2954–2961


Test problems of Assembly Line Balancing
Problem No. of task
Jackson 11


Heskia 28


Gunther 35


Kilbridge 45


Warnecke 58


Mukherje     94


2006

Kaizen Assembly: Designing, Constructing, and Managing a Lean Assembly Line - Book Information
Chris A. Ortiz
CRC Press, 26-Jun-2006 -  264 pages
http://nraoiekc.blogspot.in/2013/11/kaizen-assembly-designing-constructing.html



Assembly Line Design: The Balancing of Mixed-Model Hybrid Assembly Lines with Genetic Algorithms
Brahim Rekiek, Alain Delchambre
Springer Science & Business Media, 21-Apr-2006 - Computers - 178 pages
https://books.google.co.in/books?id=fqlO9SnTczEC

ProBalance 1.6
Mixed Model Automotive Line Balance Tutorial
http://www.proplanner.com/documents/filelibrary/documents/support_documents/ProBalance_Automative_Tutorial_PDF_274C3CD27A042.pdf


2005
Chapter on Production Planning in the book Production and Operations Management by P. Rama Murthy

Page 88.
https://books.google.co.in/books?id=8B8CN1iS8-oC&pg=PA88#v=onepage&q&f=false

Book chapter on Flow Production in Essentials of Operation Manaagement by Ray Wild.
Page 284 - Chapter starting page 283 not in preview.
https://books.google.co.in/books?id=B5j4D0U6QA0C&pg=PA284#v=onepage&q&f=false



Updated 21 May 2015
First published 21 Jan 2013

Thursday, May 21, 2015

Value Stream Mapping - The Concept




The lean production movement (Womack and Jones, 1996) developed and presented the value stream mapping (VSM) tool (Rother and Shook, 1998; Pavnaskar et al., 2003) as a functional method aimed at reorganizing production systems with a lean vision.


VSM is based on five phases put into practice by a special team created for such a purpose (Rother and Shook, 1998). The phases are:
(1) selection of a product family;
(2) current state mapping;
(3) future state mapping;
(4) defining a working plan; and
(5) achieving the working plan.

Guidelines are needed for the definition of the future state map; lean thinking provides them to assist users in how this map should be drawn (Rother and Shook, 1998; Marchwinski and Shook, 2003). These guidelines in summarized form are:
.
The production rate must be imposed by the product demand. Takt time is the concept that reflects such a rate.
.
Establishment of continuous flow where possible (unique product transfer batches).
.
Employment of pull systems between different work centres when continuous flow is not possible.
.
Only one process, called the pacemaker process, should command the production of the different parts. This process will set the pace for the entire value stream.

Value Stream Mapping Symbols
http://www.strategosinc.com/vsm_symbols.htm


Symbols and Map - Presentation
http://courses.washington.edu/ie337/Value_Stream_Mapping.pdf

VALUE-STREAM MAPPING ICONS FOR EXCEL - Excel Sheet for download
http://www.lean.org/common/display/?o=866



An evaluation of the value stream mapping tool
http://zonecours.hec.ca/documents/H2008-1-1575591.E_H08_2008_VSM_ProdSyst_Serrano-Lasa%26al.pdf



Excel Tools for Value Stream Mapping
http://www.smartdraw.com/value-stream-map/value-stream-mapping-template.htm
7 days free trail. You have to give your mail id for downloading free version.


Updated  21 May 2015
Initial post 26 Feb 2014


Tuesday, May 19, 2015

Prof Jayant Rajagopal - Industrial Engineering - Publications

Ph.D. in Industrial and Management Engineering, The University of Iowa, 1985

M.S. in Industrial and Management Engineering, The University of Iowa, 1982

B.Tech. in Chemical Engineering, The University of Madras, 1980




Chen, S.I., Norman, B.A., Rajgopal, J., and Lee, B.Y., In press, "Passive Cold Devices for Vaccine Supply Chains," Annals of Operations Research.

Brown, S.T., Schreiber, B., Cakouros, B.E., Wateska, A.R., Dicko, H.M., Connor, D.L., Jaillard, P., Mvundura, M., Norman, B.A., Levin, C., Rajgopal, J., Avella, M., Lebrun, C., Claypool, E., Paul, P., and Lee, B.Y., 2014, "The Benefits of Redesigning Benin's Vaccine Supply Chain," Vaccine, no.32, pp. 4097-4103.

Chen, S.I., Norman, B.A., Rajgopal, J., Assi, T.M., Lee, B.Y., and Brown, S.T., 2014, "A Planning Model for the WHO-EPI Vaccine Distribution Network in Developing Countries," IIE Transactions, no.1, pp. 1-13.

Esmaili, N., Norman, B.A., and Rajgopal, J., 2014, "A Heuristic Approach for Integrated Storage and Shelf-Space Allocation," 8th International Conference on Industrial Engineering and Industrial Management, XX International Conference on Industrial Engineering and Operations Management, International IIE Conference 2014, Malaga, Spain.

Mofrad, M.H., Maillart, L., Norman, B.A., and Rajgopal, J., 2014, "Dynamically Optimizing the Administration of Vaccines from Multi-Dose Vials," IIE Transactions, no.7, pp. 623-635.

Scala, N.M., Rajgopal, J., and Needy, K.L., 2014, "Managing Nuclear Spare Parts Inventories: A Data Driven Methodology," IEEE Transactions on Engineering Management, no.1, pp. 28-37.

Scala, N.M., Rajgopal, J., Vargas, L., and Needy, K.L., 2014, "Using Principal Components Analysis for Aggregating Judgments in the Analytic Hierarchy Process," International Symposium of the Analytic Hierarchy Process, Washington, D.C..

Assi, T.M., Brown, S.T., Kone, S., Norman, B.A., Djibo, A., Connor, D.L., Wateska, A.R., Rajgopal, J., Slayton, R.B., and Lee, B.Y., 2013, "Removing the Regional Level from the Niger Vaccine Supply Chain," Vaccine, no.26, pp. 2828-2834.

Haidari, L.A., Connor, D., Wateska, A.R., Brown, S., Mueller, L.E., Norman, B.A., Schmitz, M.M., Paul, P., Rajgopal, J., Welling, J.S., Leonard, J., Chen, S., and Lee, B.Y., 2013, "Augmenting transport versus increasing cold storage to improve vaccine supply chains," PLoS ONE, no.5.

Haidari, L.A., Connor, D., Wateska, A.R., Brown, S., Mueller, L.E., Norman, B.A., Schmitz, M.M., Paul, P., Rajgopal, J., Welling, J.S., Leonard, J., Claypool, E.G., Weng, Y., Chen, S., and Lee, B.Y., 2013, "Only adding stationary storage to vaccine supply chains may create and worsen transport bottlenecks.," Journal of Public Health Management and Practice, 2:S65-7.

Haidari, L.A., Connor, D.L., Wateska, A.R., Brown, S.T., Mueller, L.E., Norman, B.A., Schmitz, M.M., Paul, P., Rajgopal, J., Welling, J.S., Leonard, J., Chen, S.I., and Lee, B.Y., 2013, "Augmenting Transport versus Increasing Cold Storage to Improve Vaccine Supply Chains.," PloS one, no.5, e64303.

Norman, B.A., Nourollahi, S., Chen, S.I., Brown, S.T., Claypool, E.G., Connor, D.L., Schmitz, M.M., Rajgopal, J., Wateska, A.R., and Lee, B.Y., 2013, "A Passive Cold Storage Device Economic Model to Evaluate Selected Immunization Location Scenarios," Vaccine, no.45, pp. 5232-5238.

Scala, N.M., Rajgopal, J., and Needy, K.L., 2013, "A Base Stock Inventory Management System for Intermittent Spare Parts," Military Operations Research, no.3, pp. 63-67.

Assi, T.M., Rookkapan, K., Rajgopal, J., Sornsrivichai, V., Brown, S.T., Welling, J.S., Norman, B.A., Connor, D.L., Chen, S.I., Slayton, R.B., Laosiritaworn, Y., Wateska, A.R., Wisniewski, S.R., and Lee, B.Y., 2012, "How influenza vaccination policy may affect vaccine logistics.," Vaccine, no.30, pp. 4517-23.

Lee, B.Y., Assi, T.M., Rajgopal, J., Norman, B.A., Chen, S.I., Brown, S.T., Slayton, R.B., Kone, S., Kenea, H., Welling, J.S., Connor, D.L., Wateska, A.R., Jana, A., Wiringa, A.E., Van Panhuis, W.G., and Burke, D.S., 2012, "Impact of introducing the pneumococcal and rotavirus vaccines into the routine immunization program in Niger.," American journal of public health, no.2, pp. 269-76.

Maillart, L., Mofrad, M.H., Norman, B.A., and Rajgopal, J., 2012, "Dynamically Optimizing the Administration of Vaccines from Multi-Dose Vials," 2012 Society for Medical Decision Making Conference.

Ogirala, A., Sai, V., Kamrani, A., Rajgopal, J., Norman, B.A., Hawrylak, P.J., and Mickle, M.H., 2012, "Ultra High Speed and Low Power Flexible Architecture using State Transition Matrix Model for EPC Gen-2 Communication Protocol Processor," International Journal of Modeling and Simulation, no.3, pp. 198-205.

Scala, N.M., Rajgopal, J., and Needy, K.L., 2012, "An Inventory Criticality Classification Method for Nuclear Spare Parts: A Case Study," in Decision Making in Service Industries: A Practical Approach, J. Faulin, M.J. Fry, S.E. Grasman, and A.A. Juan, eds., CRC Press, pp. 365-391.

Rajgopal, J., 2011, "Geometric Programming," in Wiley Encyclopeida of Operations Research and Management Sciences, J.J. Cochran, ed., Wiley.

Rajgopal, J., Abdulmalek, F., Wang, L., and Norman, B.A., 2011, "Analyzing the Benefits of FRID in Reducing Off-Shelf Out-of-stock: A Simulation Approach," International Journal of Industrial and Systems Engineering, no.1, pp. 19-37.

Rajgopal, J., Connor, D.L., Assi, T.M., Norman, B.A., Chen, S.I., Bailey, R.R., Long, A.R., Wateska, A.R., Bacon, K.M., Brown, S.T., Burke, D.S., and Lee, B.Y., 2011, "The optimal number of routine vaccines to order at health clinics in low or middle income countries.," Vaccine, no.33, pp. 5512-8.

Rajgopal, J., Wang, Z., Schaefer, A.J., and Prokopyev, O., 2011, "Integrated Design and Operation of RemnantInventory Supply Chains under Uncertainty," European Journal of Operational Research, no.2, pp. 358-364.

Assi, T.M., Brown, S.T., Djibo, A., Norman, B.A., Rajgopal, J., Welling, J.S., Chen, S.I., Bailey, R.R., Kone, S., Kenea, H., Connor, D.L., Wateska, A.R., Jana, A., Wisniewski, S.R., Van Panhuis, W.G., Burke, D.S., and Lee, B.Y., 2011, "Impact of changing the measles vaccine vial size on Niger's vaccine supply chain: a computational model.," BMC public health, p. 425.

Hawrylak, P.J., Ogirala, A., Norman, B.A., Rajgopal, J., and Mickle, M.H., 2011, "Enabling Real-Time Management and Visibility with RFID," in Management Engineering for Effective Healthcare Delivery: Principles and Applications, A. Kolker, and P. Story, eds., IGI Global.

Lee, B.Y., Assi, T.M., Rookkapan, K., Connor, D.L., Rajgopal, J., Sornsrivichai, V., Brown, S.T., Welling, J.S., Norman, B.A., Chen, S.I., Bailey, R.R., Wiringa, A.E., Wateska, A.R., Jana, A., Van Panhuis, W.G., and Burke, D.S., 2011, "Replacing the measles ten-dose vaccine presentation with the single-dose presentation in Thailand.," Vaccine, no.21, pp. 3811-7.

Lee, B.Y., Assi, T.M., Rookkapan, K., Wateska, A.R., Rajgopal, J., Sornsrivichai, V., Chen, S.I., Brown, S.T., Welling, J., Norman, B.A., Connor, D.L., Bailey, R.R., Jana, A., Van Panhuis, W.G., and Burke, D.S., 2011, "Maintaining vaccine delivery following the introduction of the rotavirus and pneumococcal vaccines in Thailand.," PloS one, no.9, e24673.

Shylo, O.V., Luangkesorn, L., Prokopyev, O.A., Rajgopal, J., and Schaefer, A., 2011, "Managing Patient Backlog in a Surgical Suite that uses a Block-Booking Scheduling System," 2011 Winter Simulation Conference, R.R. Creasey, M. Fu, J. Himmelspach, S. Sain, and K.P. White, eds., Phoenix, AZ.

Shylo, O.V., Prokopyev, O., and Rajgopal, J., 2011, "On Algorithm Portfolios and Restart Strategies," Operations Research Letters, no.1, pp. 49-52.

Lee, B.Y., Norman, B.A., Assi, T.M., Chen, S.I., Bailey, R.R., Rajgopal, J., Brown, S.T., Wiringa, A.E., and Burke, D.S., 2010, "Single versus multi-dose vaccine vials: an economic computational model.," Vaccine, no.32, pp. 5292-300.

Maillart, L., Kamrani, A., Norman, B., Rajgopal, J., and Hawrylak, P., 2010, "Optimizing RFID Tag-Inventorying Algorithms," IIE Transactions, no.9, pp. 690-702.

Scala, N.M., Rajgopal, J., and Needy, K.L., 2010, "Influence Diagram Modeling of Nuclear Spare Parts Process," 2010 IIE Research Conference, Cancun, MX.

Scala, N.M., Rajgopal, J., and Needy, K.L., 2010, "Using the Analytic Hierarchy Process in Group Decision Making for Nuclear Spare Parts," 31st ASEM National Conference, pp. 191-199, Fayetteville, AR.

Rajgopal, J., Wang, Z., Schaefer, A.J., and Prokopyev, O., 2009, "Effective Management Policies for Remnant Inventory Supply Chains," IIE Transactions, no.5, pp. 437-447.

Paulk, M., Needy, K.L., and Rajgopal, J., 2009, "Identifying Software Process Outliers," ASQ Software Quality Professional, no.2, pp. 28-37.

Scala, N.M., Rajgopal, J., and Needy, K.L., 2009, "Risk and Spare Parts Inventory in electric Utilities," 2009 IIE REsearch Conference, Miami, FL.

Scala, N.M., Needy, K.L., and Rajgopal, J., 2009, "Decision Making and Tradeoffs in the Management of Spare Parts Inventory at Utilities," 30th ASEM National Conference, pp. 257-263, Springfield, MO.

Rajgopal, J., Norman, B.A., Wang, L., and Abdulmalek, F., 2008, "A Simulation Study of RFID for Retail Shelf Replenishment," 2008 Industrial Engineering Research Conference, pp. 758-763, Vancouver, BC.

Shuman, L.J., Bidanda, B., Besterfield-Sacre, M.E., and Rajgopal, J., 2008, "Internationalizing the Engineering Curriculum," IIE Annual Conference and Expo 2008 Industrial Engineering Research Conference, Vancouver, BC.

Abdulmalek, F.A., and Rajgopal, J., 2007, "Analyzing the Benefits of Lean Manufacturing and Value Stream Mapping via Simulation: A Process Sector Case Study," International Journal of Production Economics, no.1, pp. 223-236.

Wang, L., Norman, B.A., and Rajgopal, J., 2007, "Maximizing Read Accuracy by Optimally Locating RFID Interrogators," in RFID Handbook: Applications, Technology, Security, and Privacy, S. Ahson, and M. Ilyas, eds., CRC Press, pp. 181-198.

Wang, L., Norman, B.A., and Rajgopal, J., 2007, "Placement of Multiple RFID Reader Antennas to Maximize Portal Read Accuracy," International Journal of Radio Frequency Identification Technology and Applications, no.3, pp. 260-277.

Abdulmalek, F.A., Rajgopal, J., and Needy, K., 2006, "A Classification Model for the Process Industry to Guide the Implementation of Lean," Engineering Management Journal, no.2, pp. 15-25.

Wang, Z., Rajgopal, J., and Schaefer, A.J., 2006, "An Efficient Heuristic for Location/Distribution Decisions with Remnant Inventories," IIE Research Conference, Orlando, FL.

Besterfield-sacre, M.E., Norman, B.A., Bidanda, B., Needy, K., and Rajgopal, J., 2005, "Integrating and Synthesizing the Industrial Engineering Curriculum via an Unstructured Problem Solving Course," American Society for Engineering Education Conference Proceedings, Portland, OR.

Rajgopal, J., and Mazumdar, M., 2004, "An Optimum System Based Component Testing Approach for Evaluating Software Reliability," Net.ObjectDays Workshop on Testing of Component-Based Systems (TECOS 2004) and Software Quality (SOQUA 2004), S. Beydeda, V. Gruhn, J. Mayer, R. Reussner, and F. Schweiggert, eds., pp. 63-76.

Norman, B., Besterfield-sacre, M.E., Bidanda, B., Needy, K., and Rajgopal, J., 2004, "A Conceptual Model for Integrating and Synthesizing the Industrial Engineering Curriculum," American Society for Engineering Education Conference Proceedings, Salt Lake City, UT.

Norman, B.A., Besterfield-Sacre, M.E., Needy, K.L., and Rajgopal, J., 2004, "Integration and Synthesis of the Industrial Engineering Curriculum," IIE Research Conference, Houston, TX.

Olson, S., Boros, S., Schaefer, A.J., and Rajgopal, J., 2004, "Evaluation of Operating Policies for Remnant Inventory Systems via Simulation," IIE Research Conference, Houston, TX.

Adbullah, F., and Rajgopal, J., 2003, "Lean Manufacturing in the Process Industry," IIE Research Conference, Portland, OR.

Rajgopal, J., and Bricker, D.L., 2002, "Solving Posynomial Geometric Programming Problems via Generalized Linear Programming," Computational Optimization and Applications, no.1, pp. 95-109.

Rajgopal, J., and Mazumdar, M., 2002, "Modular Test Plans for Certification of Softwware Reliability," IEEE Transactions on Software Engineering, no.4, pp. 358-363.

Abdullah, F., Rajgopal, J., and Needy, K.L., 2002, "A taxonomy of the Process Industry with a View to Lean Manufacturing," American Society for Engineering Management, pp. 314-321, Tampa, FL.

Adickes, M.D., Billo, R.E., Norman, B.A., Banerjee, S., Nnaji, B.O., and Rajgopal, J., 2002, "Optimization of Indoor Wireless Communication Network Layouts," IIE Transactions, no.9, pp. 823-836.

Rajgopal, J., 2001, "Principles and Applications of Operations Research," in Maynard's Industrial Engineering Handbook, K.B. Zandin, ed., McGraw Hill, 11.27-11.44.

Rajgopal, J., and Mazumdar, M., 2001, "Software Reliability via Modular Testing," 10th Industrial Engineering Research Conference, Dallas, TX.

Rajgopal, J., and Mazumdar, M., 2001, "System Based Component Test Plan for Reliability Demonstration: A Review and Survey of the State-of-the-Art," in Handbook of Statistics: Advances in Reliability, N. Balakrishnan, and C.R. Rao, eds., Elsevier Science, pp. 659-677.

Aiyer, J.P., and Rajgopal, J., 2001, "Managing Cable TV Commercial Inventories via Program Promotion," Marketing Intelligence and Planning, no.1, pp. 45-54.

Bidanda, B., Shuman, L.J., Rajgopal, J., Besterfield-Sacre, M., and Ruibal, C., 2001, "Flexible Doctoral Programs for the International Faculty: A Refined Model with Preliminary Results," International Conference on Engineering Education, ICEE-01, Oslo/Bergen, Norway.

Gomes, C.J., Onipede, O., Lovell, M., Norman, B.A., and Rajgopal, J., 2001, "Numerical Analysis of Springback Using a Response Surface Methodology," Transactions of the 29th North American Manufacturing Research Conference, pp. 89-96.

Ozturk, U.A., Norman, B.A., and Rajgopal, J., 2001, "A Simulation Analysis of Printed Circuit Board Operations in a Mixed Production Environment," Annual Industrial Engineering Solutions Conference, Dallas, TX.

Rajgopal, J., 2000, "A Transportation Model for Scheduling Promotions on Cable TV," 9th Industrial Engineering Research Conference, Cleveland, OH.

Rajgopal, J., and Mazumdar, M., 2000, "Minimum Cost Test Plans for a Series System with Imperfect Interfaces," in Perspectives in Statistical Science, A.K. Basu, J.K. Ghosh, P.K. Sen, and B.K. Sinha, eds., Oxford University Press, pp. 209-218.

Needy, K.L., and Rajgopal, J., 2000, "Developing a manufacturing Strategic Plan: A Field Study," Annual Industrial Engineering Solutions Conference, Cleveland, OH.

Rajgopal, J., Mazumdar, M., and Majety, S.V., 1999, "Optimum combined Test Plans for Systems and Components," IIE Transactions, no.6, pp. 481-490.

Federowicz, A.J., and Rajgopal, J., 1999, "Robustness of Posynomial Geometric Programming Optima," Mathematical Programming, no.2, pp. 421-431.

Mahmood, F., Bidanda, B., and Rajgopal, J., 1999, "WEDM Process Modeling using the Regression Approach," 8th Industrial Engineering Research Conference, Phoenix, AZ.

Majety, S.V., Dawande, M., and Rajgopal, J., 1999, "Optimal Reliability Allocation with Discrete cost-Reliability Data for Components," Operations Research, no.6, pp. 899-906.

Rajgopal, J., and Mazumdar, M., 1998, "System Based Component Test Plan for Reliability Inferences," in Frontiers on Reliability, A.P. Basu, S.K. Basu, and S. Mukhopadhyay, eds., World Scientific Press, pp. 295-302, Singapore.

Rajgopal, J., Bidanda, B., and Shuman, L.J., 1998, "Flexible Doctoral Programs for International Faculty," International Conference on Engineering Education, ICEE-98, pp. 149-151, Rio de Janeiro.

Rajgopal, J., and Mazumdar, M., 1997, "Minimum Cost Component Test Plans for Demonstrating Reliability of a Parallel System," Naval Research Logistics, no.5, pp. 401-418.

Rajgopal, J., Needy, K.L., and Porter, J.D., 1997, "Combining International Experience and Industrial Relevance in a Capstone Engineering Design Course," 1997 ASEE/IEEE Frontiers in Education Conference, Pittsburgh, PA.

Aiyer, J.P., and Rajgopal, J., 1997, "Commercial Sales in Cable Television - An Overview and a Linear Model," Mid-American Journal of Business, no.1, pp. 27-33.

Majety, S.V., and Rajgopal, J., 1997, "Dynamic Penalty Function for Evolutionary Algorithms with an Application to a Reliability allocation," 6th Industrial Engineering Research Conference, pp. 36-41, Miami Beach, FL.

Rajgopal, J., and Mazumdar, M., 1996, "A System Based Component Test Plan for a Series System, with Type-II Censoring," IEEE Transactions on Reliability, no.3, pp. 375-378.

Rajgopal, J., and Mazumdar, M., 1995, "Designing Component Test Plans for System Reliability via Mathematical Programming," International Journal of Reliability, Quality and Safety Engineering, no.1, pp. 35-48.

Rajgopal, J., and Mazumdar, M., 1995, "Designing Test Plans for Series System Reliability via Mathematical Programming," Technometrics, no.2, pp. 195-212.

Tunasar, C.E., and Rajgopal, J., 1995, "An Evolutionary Algorithm with an Application to a Lot Sizing Problem," 4th Industrial Engineering Research Conference, pp. 852-858, Nashville, TN.

Rajgopal, J., 1994, "Investigations in an Alternative Approach to Geometric Programming," 1994 NSF Design and Manufacturing Grantees Conference, pp. 271-272, Cambridge, MA.

Rajgopal, J., Mazumdar, M., and Coit, D., 1994, "Design of System-Based Component Test Plans for Series Systems with Gamma Distributed Component Lifetimes," 3rd Industrial Engineering Research Conference, pp. 13-18, Atlanta, GA.

Rajgopal, J., Mazumdar, M., and Savits, T.H., 1994, "Some Properties of the Poisson Distribution with an Application to Reliability Testing," Probability in the Engineering and Informational Sciences, no.3, pp. 345-354.

Rajgopal, J., and Mazumdar, M., 1993, "Optimum System Based Component Test Plans," 2nd industrial Engineering Research Conference, pp. 247-251, Los Angeles, CA.

Rajgopal, J., Bidanda, B., and Burns, G., 1993, "Integrating Group Technology and TSP for Scheduling Operations with Sequence Dependent Setup Times," 2nd industrial Engineering Research Conference, pp. 837-841, Los Angeles, CA.

Bricker, D.L., Choi, J.C., and Rajgopal, J., 1993, "On Geometric Programs Having Negative Degrees of Difficulty," European Journal of Operational Research, no.3, pp. 427-430.

Rajgopal, J., 1992, "An Alternative Approach to the Refined Duality theory of Geometric Programming," Journal of Mathematical Analysis and Applications, no.1, pp. 266-288.

Rajgopal, J., 1992, "Nonlinear Programming," in Maynard's Industrial Engineering Handbook, W.K. Hodson, ed., McGraw Hill, 14.177-14.200.

Rajgopal, J., and Bidanda, B., 1992, "On the Use of Statistical Design in Manufacturing Engineering Education," International Journal of Applied Engineering Education, no.4.

Rajgopal, J., and Bricker, D.L., 1992, "On Subsidiary Problems in Geometric Programming," European Journal of Operational Research, no.1, pp. 102-113.

Rajgopal, J., and Bidanda, B., 1991, "Scheduling Parallel Machines with Two Setup Classes," International Journal of Production Research, no.12, pp. 2443-2458.

Rajgopal, J., and Bricker, D.L., 1990, "Geometric Programming as a Special Case of Semi-Infinite Linear Programming," Journal of Optimization Theory and Applications, no.3, pp. 455-475.

Rajgopal, J., and Frabotta, M., 1990, "Manufacturing Resource Planning - MRP II," in Handbook of the Automated Factory, B. Bidanda, and D.I. Cleland, eds., TAB Scientific Publishers, pp. 567-588.

Belegundu, A.D., Rajan, S.D., and Rajgopal, J., 1990, "Exponential Approximations in Optimal Design," AIAA/ASME/ASCE/AHS/ASC 31st Structures, Structural Dynamics and Materials Conference, pp. 137-150, Long Beach, CA, NASA.

Bidanda, B., and Rajgopal, J., 1990, "Optimal Selection of Workholding Devices for Concentric Rotational Parts," IIE Transactions, no.1, pp. 65-72.

Rajgopal, J., and Mazumdar, M., 1988, "A Type II Censored, Log-Test Time Based, Component Testing Procedure For Parallel Systems," IEEE Transactions on Reliability, no.R-37, pp. 406-412.

Hundal, T.S., and Rajgopal, J., 1988, "An Extension of Palmer's Heuristic for the Flow-Shop Scheduling Problem," International Journal of Production Research, no.6, pp. 1119-1124.

Bricker, D.L., and Rajgopal, J., 1983, "Yet Another Geometric Programming Dual Algorithm," Operations Research Letters, no.4, pp. 177-180.

Prof Karen M. Bursic - Industrial Engineering - Publications

Doctorate in Industrial Engineering, University of Pittsburgh, 1990

PhD in Industrial Engineering, University of Pittsburgh, 1990

Masters in Engineering Management, University of Pittsburgh, 1987

B.S. in Industrial Engineering, University of Pittsburgh, 1984


Engineering Economic Analysis

Engineering Education

Engineering Management





Bursic, K.M., Clark, R., Besterfield-Sacre, M., and Budny, D., 2014, "Preliminary Experiences with 'Flipping' a Freshman Engineering Program Course," 6th First Year Engineering Experience (FYEE) Conference, College Station TX.

Bursic, K.M., Steiner, S., Besterfield-Sacre, M., and Shuman, L., 2014, "An Approach to Evaluate Engineering Global Preparedness in Industrial Engineering Curricula," 2014 Industrial Engineering Research Conference, Montreal, QC.

Bursic, K.M., 2012, "Does the Use of Clickers Increase Conceptual Understanding in the Engineering Economy Classroom," 2012 American Society for Engineering Education Annual Conference, San Antonio Texas.

Bursic, K.M., Shuman, L., Besterfield-Sacre, M., Vidic, N., and Siewiorek, N., 2012, "CCLI: Model Eliciting Activities: Experiments and Mixed Methods to Assess Student Learning III," American Society for Engineering Education, San Antonio, TX.

Siewiorek, N., Shuman, L.J., Besterfield-sacre, M.E., Vidic, N., and Bursic, K.M., 2012, "Students' Confidence Levels in Technical Concept Knowledge with Model Eliciting Activities," San Antonio, TX.

Bursic, K.M., Shuman, L., and Besterfield-sacre, M.E., 2011, "Improving Student Attainment of ABET Outcomes Using Model-Eliciting Activities (MEAs)," American Society for Engineering Education, Vancouver, BC.

Bursic, K.M., Shuman, L., Besterfield-sacre, M.E., Vidic, N., and Yildirim, P., 2011, "CCLI: Model Eliciting Activities: Experiments and Mixed Methods to Assess Student Learning - Part II," American Society for Engineering Education, Vancouver, BC.

Bursic, K.M., Vidic, N., Shuman, L., Besterfield-sacre, M.E., Yildirim, T.P., and Siewiorek, N., 2011, "Leaning Impacts Gained from Introducing Model Eliciting Activities (MEAs) in an Introductory Statistics Course," Industrial Engineering Research Conference, Reno, NV.

Bursic, K.M., Budny, D., Lund, L., and Vidic, N., 2010, "Reviewing the Success of a Freshman Programming Course," ASEE North Central Section Regional Conference.

Bursic, K.M., Shuman, L., Besterfield-sacre, M.E., Yildirim, T.P., and Siewiorek, N., 2010, "Improving Conceptual Learning in Engineering Economy using Model-Eliciting Activities (MEAs)," Industrial Engineering Research Conference, Cancun, Mexico.

Bursic, K.M., Shuman, L., Besterfield-sacre, M.E., Clark, R., and Yildirim, P., 2009, "E-MEAs: Introducing an Ethical Component to Model Eliciting Activities," American Society for Engineering Education, Austin, TX.

Bursic, K.M., and LaScola, K., 2008, "Implementing International Requirements in Undergraduate Industrial Engineering Programs," American Society for Engineering Education.

Bursic, K.M., Needy, K.L., Norman, B., Besterfield-sacre, M.E., and Hunsaker, B., 2007, "The Challenges of Undergraduate Industrial Engineering Curriculum Reform at the University of Pittsburgh," Industrial Engineering Research Conference.

Bursic, K.M., 2006, "Applying Engineering Economic Analysis to Contemporary Problems with Global and Societal Implications," American Society for Engineering Education.

Bursic, K.M., 2006, "Engineering Economy."

Bursic, K.M., 2004, "Self-Managed Production Teams," in Field Guide to Project Management, 2nd ed..

Bursic, K.M., Needy, K.L., and Wilson, J.P., 2003, "Integrating Engineering Economic Analysis Across the Engineering Curriculum," American Society for Engineering Education.

Bursic, K.M., Atman, C.J., Chimka, J.R., and Umphred, H.N., 1999, "A Comparison of Freshmen and Senior Engineering Design Processes," Design Studies.

Bursic, K.M., and Atman, C.J., 1998, "Verbal Protocol Analysis as a Method to Document Engineering Student Design Processes," Journal of Engineering Education.

Cleland, D., Bursic, K.M., Puerzer, R., and Vlasak, Y., 1998, "Project Management Casebook and Instructor's manual," Project Management Institute.

Bursic, K.M., and Atman, C.J., 1997, "Information Gathering: A Critical Step for Quality in the Design Process," Quality Management Journal.

Bursic, K.M., Chimka, J.R., and Atman, C.J., 1997, "Describing Student Design Behavior," American Society for Engineering Education.

Bursic, K.M., and Atman, C.J., 1996, "Teaching Engineering Design: Can Reading a Textbook Make a Difference," Research in Engineering Design.

Bursic, K.M., Atman, C.J., and Lozito, S.L., 1996, "An Application of Protocol Analysis to the Engineering Design Process," American Society for Engineering Education.

Bursic, K.M., and Atman, C., 1995, "Do Freshmen Design Texts Adequately Define the Engineering Design Process?," American Society for Engineering Education.

Bursic, K.M., and Atman, C., 1995, "Gathering Information: What Do Students Do?," American Society for Engineering Education.

Cleland, D., 1993, "Project Management Casebook and Instructor's Guidelines," Project Management Institute.

Bursic, K.M., 1992, "Strategies and Benefits of the Successful Use of Teams in Manufacturing Organizations," IEEE Transactions on Engineering Management.

Bursic, K.M., and Cleland, D.I., 1992, "Strategic Technology Management: Systems for Products and Processes," American Management Association.

Bursic, K.M., 1991, "The Use of Teams for Improving Productivity and Quality in Manufacturing," Conference on Productivity and Quality Research.

Bursic, K.M., and Cleland, D., 1991, "Strategic Technology Management," Engineering Management Journal.

Bursic, K.M., 1990, "Production Teams in Manufacturing," in The Automated Factory Handbook, TAB Books.

Bursic, K.M., Cleland, D., and Wain, H.W., 1990, "A Strategic Technology Management System," Second International Conference on Management of Technology.

Prof Bidanda Bopaya - Industrial Engineering - Publications

Ph.D. in Industrial and Management Systems Engineering, The Pennsylvania State University, 1987

M.S. in Science & Technology, Western Carolina University, 1983

B.S. in Electrical Engineering, National Institute of Technology (ex KREC - Surathkal, University of Mysore), 1976



Bidanda, B., and Redfern, M., "Development of a Microcomputer Based Slip Tester," To appear in Computers and Industrial Engineering Journal.

Hu, G., Wang, L., Chen, Y., and Bidanda, B., "An Oligopoly Model to Analyze the Market and Social Welfare for Green Manufacturing Industry," To appear in Journal of Cleaner Production.

Basu, S., and Bidanda, B., 2013, "Eco-efficient construction and building materials," in Shortcomings of eco-labelling of construction and building materials, E.A. Pacheco-Torgal, ed., Woodhead Publishing.

Bidanda, B., and Norman, B.A., 2012, "Enhancing Endoscope Reprocessing within the VA Health System," Industrial & Systems Engineering Research Conference, Orlando, Florida.

Desai, S., Bidanda, B., and Lovell, M., 2012, "Material and process Selection in product design using decision-making techniques (AHP)," European Journal on Industrial Engineering, no.3.

Wu, S., Shuman, L., Bidanda, B., Baleban, C., and Sochats, K., 2012, "A Hybrid Modeling Framework to Simulate Disaster Response Decisions," International Journal of Advanced Intelligence Paradigms, no.1.

Bidanda, B., Hu, G., Shankar, M.R., Abolghasem, S., and Basu, S., 2011, "Assessing the Environmental Footprint of Manufactured Products: A Survey of Current Literature," International Journal of Production Economics.

Bidanda, B., Hu, G., Wang, L.Z., and Chen, Y., 2011, "An Oligopoly Model to Analyze the Market and Social Welfare for Green Manufacturing Industry," International Conference on Production Research, Stuttgart.

Hu, G., Wang, L.Z., Chen, Y., and Bidanda, B., 2011, "An Oligopoly Model to Analyze the Market and Social Welfare for Green Manufacturing Industry," International Conference on Production Research, Stuttgart.

Arisoy, O., and Bidanda, B., 2009, "Strategic Decision Making in Global Supply Networks," in Strategic Information Systems, M.G. Hunter, ed..

Arisoy, O., Azim, M., and Bidanda, B., 2009, "Project Management in a Flat World Circa 2025," in Project Management Circa 2025, B. Bidanda, and D. Cleland, eds., Project Management Institute.

Cleland, D., and Bidanda, B., 2009, "PROJECT MANAGEMENT CIRCA 2025," Project Management Institute.

Gaussin, M., Hu, G., Shankar, R., and Bidanda, B., 2009, "Assessing the Environmental Footprint of Manufactured Products: A Survey of Current Literature," International Conference on Production Research, Shanghai.

Hu, G., and Bidanda, B., 2009, "A Product Upgrade Decision Model for Sustainable Manufacturing," Industrial Engineering Research Conference, Miami, Florida.

Hu, G., and Bidanda, B., 2009, "Modeling Sustainable Product Life Cycle Decision Support Systems," Int. J. Production Economics.

Hu, G., Wang, L., and Bidanda, B., 2009, "A Multi-objective Model for Project Portfolio Selection to Implement Lean and Six Sigma Concepts," International Journal of Production Research, no.23, pp. 6611-6625.

Hu, G., Wang, L., and Bidanda, B., 2009, "Sustainable Manufacturing and Project Management Circa 2025," in Project Management Circa 2025, B. Bidanda, and D. Cleland, eds., Project Management Institute.

Bidanda, B., and Bartolo, P., 2008, "VIRTUAL PROTOTYPING & BIO-MANUFACTURING IN MEDICAL APPLICATIONS," Springer Science Publishers.

Arisoy, O., and Bidanda, B., 2008, "Strategic Decision Making in Global Supply Networks," in Encyclopedia of Networked & Virtual Organizations, M.M. Cunha, and G.D. Putnik, eds., Information Science Reference, pp. 1509-1515.

Bunce, M., Wang, L., and Bidanda, B., 2008, "Leveraging Six Sigma with Industrial Engineering tools in Crateless Retort Production," International Journal of Production Research, pp. 6701-6719.

Dhawan, A., Srinivasan, S., Rajib, P., and Bidanda, B., 2008, "Minimizing total cost and regular and emergency sources: a neuro-dynamic programming approach," International Journal of Production Research.

Wu, S., Shuman, L., Bidanda, B., Kelley, M., Sochats, K., and Balaban, C., 2008, "Agent-based discrete event simulation modeling for disaster responses," J. Fowler, and S. Mason, eds., pp. 1908-13.

Wu, S., Shuman, L., Bidanda, B., Prokopyev, O., Kelley, M., Sochats, K., and Balaban, C., 2008, "Simulation-based decision support system for real-time disaster response management," J. Fowler, and S. Mason, eds., pp. 58-63.

Bartolo, P., and Bidanda, B., 2007, "BIO-MATERIALS AND PROTOTYPING APPLICATIONS IN MEDICINE," Springer Science Publishers.

Cohen, Y., Wang, M., and Bidanda, B., 2007, "Modeling and implementation of agent-based discrete industrial automation," in Innovative algorithms and techniques in automation, industrial electronics and telecommunications, K. Elleithy, M. Karim, A. Mahmood, and T. Sobh, eds., Springer, pp. 535-541.

Desai, S., Bidanda, B., and Bartolo, P., 2007, "Metallic and Ceramic Biomaterials: Current and Future Directions," in Bio Materials and Prototyping Applications in Medicine, P. Bartolo, and B. Bidanda, eds., Springer.

Hu, G., and Bidanda, B., 2007, "Modeling Sustainable Product Lifecycle Decision Support Systems," Chile.

Hu, G., Wang, L., and Bidanda, B., 2007, "Project Portfolio Selection for Implementing Lean and Six Sigma Concepts," Nashville.

Hu, G., Wang, L., Wang, Y., and Bidanda, B., 2007, "A New Model for Closed Loop Product Lifecycle Systems," Nashville.

Srinivasan, S., Jain, C., and Bidanda, B., 2007, "Software and Other Project Management Practices in India," in Project Manager's Handbook: Applying Best Practices across Global Industries, D. Cleland, and L.R. Ireland, eds., McGraw Hill.

Wang, L., Hu, G., and Bidanda, B., 2007, "A Game Theoretic Model of the Market Competition between Green and Ordinary Products," Proceedings of the 2007 Industrial Engineering Research Conference, Nashville.

Wu, S., Shuman, L., Bidanda, B., Kelley, M., Sochats, K., and Balaban, C., 2007, "Disaster policy optimization: A simulation based approach," pp. 872-877, Nashville.

Wu, S., Shuman, L., Bidanda, B., Kelley, M., Sochats, K., and Balaban, C., 2007, "Embedding GIS in disaster simulation," 27th Annual ESRI International User Conference.

Wu, S., Shuman, L., Bidanda, B., Kelley, M., Sochats, K.M., and Balaban, C., 2007, "Embedding GIS in disaster simulation."

Wu, S., Shuman, L.J., Bidanda, B., Kelley, M., Lawson, B., Sochats, K.M., and Balaban, C.D., 2007, "System implementation issues of Dynamic Discrete Disaster Decision Simulation System (D4S2) - Phase I," R.R. Barton, B. Biller, S.G. Henderson, M. Hsieh, J. Shortle, and J.D. Tew, eds., pp. 1127-34.

Bidanda, B., and Arisoy, O., 2006, "Project Management in an Outsourcing Environment," in The Global Project Management Handbook (2nd Edition), D. Cleland, and R. Gareis, eds..

Bidanda, B., Arisoy, O., and Shuman, L.J., 2006, "Colombia & the New Global Economy: Implications of Tratado de Libre Comercio for Colombian Industry, Engineers & Engineering Educators," Revista de ingenieria, pp. 83-90.

Bidanda, B., Arisoy, O., and Shuman, L.J., 2006, "Offshoring Manufacturing: Implications for engineering jobs and education: A survey and case study," Robotics and Computer Integrated Manufacturing, no.6.

Arisoy, O., Bidanda, B., and Shuman, L., 2006, "Multi-expert multi-criteria decision making in outsourcing," Orlando.

Arisoy, O., Gokhan, M., Needy, K.L., and Bidanda, B., 2006, "Activity Based Costing and Life Cycle Costing in Outsourcing Decision Analysis," Orlando.

Cohen, Y., Wang, M.E., and Bidanda, B., 2006, "Modeling and Implementation of Agent-Based Discrete Industrial Automation," International Conference on Industrial Electronics, Technology & Automation.

Creehan, K., and Bidanda, B., 2006, "Computer-Aided Reverse Engineering of the Human Musculo-skeletal system," Virtual & Physical Prototyping, no.2.

Hu, G., Wang, Y., and Bidanda, B., 2006, "PLM Systems for Network-centric manufacturing," Orlando.

Hu, G., Wang, Y., and Bidanda, B., 2006, "Product Life cycle management challenges in trans-national environments," Orlando.

Lai, J.P., Shuman, L.J., and Bidanda, B., 2006, "A Surrogate Approach to Simulation Optimization," Orlando.

Puthpongsiriporn, T., Porter, D.J., Bidanda, B., Wang, M.E., and Billo, R.E., 2006, "Attribute-Level Neighbor Hierarchy Construction Using evolved Pattern-based Knowledge Induction," IEEE Transactions on Knowledge and Data Engineering, no.7.

Bidanda, B., Arisoy, O., and Shuman, L., 2005, "Manufacturing Outsourcing: Implications for Engineering Jobs & Education," FAIM 2005 Conference, pp. 884-892, Bilbao, Spain.

Bidanda, B., Arisoy, O., and Shuman, L.J., 2005, "The New Global Economy: Implications for Manufacturing Engineers and Educators."

Bidanda, B., Ariyawongrat, P., Needy, K.L., Norman, B.A., and Tharmmaphornphilas, W., 2005, "Human Related Issues in Manufacturing Cell Design, Implementation, and Operation: A Review & Survey," International Journal of Computers & Industrial Engineering, no.48, pp. 507-523.

Bidanda, B., Shuman, L.J., Thomes, K., and Arisoy, O., 2005, "Adapting Engineering Coursework for Increased Global Relevance," Annual Conference of the American Society for Engineering Education, Salt Lake City.

Alrashdan, A., Motavalli, S., and Bidanda, B., 2005, "Creation of Surface Models for Re-engineering of Manufactured Parts," International Conference of Production Research, Italy.

Cohen, Y., Bidanda, B., and Rokach, L., 2005, "A New Technique for Modeling & Implementation of Agent-Based Discrete Industrial Automation," FAIM 2005 Conference, pp. 424-431, Bilbao, Spain.

Creehan, K., and Bidanda, B., 2005, "Computer Aided Reverse Engineering of Human Tissues," pp. 155-160.

Needy, K., Norman, B.N., Besterfield-Sacre, M.B., Rajgopal, J., and Bidanda, B., 2005, "Integration and Synthesis of the Industrial Engineering Curriculum via an Unstructured Problem Solving Course," Annual Conference of the American Society for Engineering Education, Salt Lake City.

Shuman, L.J., Bidanda, B., Thomes, K., and Feick, L., 2005, "The Global and Societal Challenge - An Innovative Approach to ABET Criterion 3.H. and beyond," Annual Conference of the American Society for Engineering Education, Salt Lake City.

Bidanda, B., and Bartolo, P., 2004, "Guest Editorial - Product Development," International Journal of Product Development, no.2.

Bidanda, B., and Desai, S., 2004, "Strategic planning models for prototyping and product development centers," International Journal of Product Development, no.2.

Norman, B.A., Besterfield-sacre, M.E., Bidanda, B., Needy, K.L., and Rajgopal, J., 2004, "A Conceptual Model for Integrating and Synthesizing the industrial engineering curriculum," American Society for Engineering Education Annual Conference, Salt Lake City.

Sunanta, O., and Bidanda, B., 2004, "A Comparison of Manual and Mechanical Lapping Methods on Valve Re-conditioning," Industrial Engineering Research Conference, Houston.

Bidanda, B., Desai, S., and Lovell, M., 2003, "The Business of Virtual and Rapid Prototyping," pp. 91-95.

Needy, K.L., Nachtmann, H., Roztocki, N., Warner, R.N., and Bidanda, B., 2003, "Implementing Activity Based Costing Systems in Small Manufacturing Firms: A Field Study," Engineering Management Journal, no.1, pp. 3-10.

Needy, K.L., Norman, B.A., Bidanda, B., Ariyawongrat, P., Tharmmaphornphilas, W., and Warner, R.C., 2002, "Assessing human capital: A lean manufacturing example," Engineering Management Journal, no.3, pp. 35-39.

Norman, B.A., Tharmmaphornphilas, W., Needy, K.L., Bidanda, B., and Warner, R.C., 2002, "Worker Assignment in cellular manufacturing considering technical and human skills," International Journal of Production Research, no.6, pp. 1479-1492.

Bidanda, B., Needy, K.L., and Norman, B.A., 2001, "Worker Assignment for cellular manufacturing considering technical, human, and lean skills," 2001 NSF Design, Service and Manufacturing Grantees and Research Conference, Tampa, FL.

Bidanda, B., Shuman, L.J., Rajgopal, J., Besterfield-sacre, M.E., and Rubial, C., 2001, "Flexible Doctoral Programs for International faculty: A Refined Model with preliminary results," International Conference for Engineering Education, Oslo.

Creehan, K., and Bopaya, B., 2001, "Computer Aided Reverse Engineering of Human Tissues and Structures," International Conference of Production Research, Prague.

Needy, K.L., Norman, B.A., Bidanda, B., Tharmmphornphilas, W., Aiyawongrat, P., and Warner, R.C., 2001, "Human Capital Assessment in Lean Manufacturing," American Society for Engineering Management Proceedings, pp. 233-239, Huntsville, AL.

Rafe, G.E., Needy, K.L., Bidanda, B., and Schmidt, T.A., 2001, "Delivering continuous manufacturing education and training via internet-based distributed virtual laboratories," 2001 Frontiers in Education Conference, Reno, NV.

Sunant, O., and Bidanda, B., 2001, "A Fuzzy Logic Advisory System for Flat Surface Lapping," International Conference of Production Research, Prague.

Bidanda, B., 2000, "Assembly Line Balancing," in Maynard Industrial Engineering Handbook, K. Zandin, ed., McGraw Hill.

Bidanda, B., Aguwa, C., and Nnaji, B., 2000, "A Manufacturing Modernization Model for Developing Countries," 5th USA-Africa Conference on Manufacturing Technology, Abuja, Nigeria.

Bidanda, B., Needy, K.L., and Norman, B.A., 2000, "Worker Assignment for cellular manufacturing considering human issues," 2000 NSF Design and Manufacturing Research Conference, Vancouver, British Columbia.

Bidanda, B., Needy, K.L., Norman, B.A., and Warner, R., 2000, "Skills and Cells," World Symposium GT-CM 2000, San Juan, Puerto Rico.

Billo, R.E., Bidanda, B., and Adickes, M., 2000, "Bar Codes and Other Data Collection Methods," in Maynard Industrial Engineering Handbook, K. Zandin, ed., McGraw Hill.

Carnahan, B., Warner, R.C., Bidanda, B., and Needy, K.L., 2000, "Predicted glass furnace output using statistical and neural computing methods," International Journal of Production Research, no.6, pp. 1255-1269.

Maitra, A., Bidanda, B., and Nnaji, B., 2000, "A Framework for Task Level Programming in Automated Storage and Retrieval Systems," 9th Industrial Engineering Research Conference, Cleveland, OH.

Needy, K.L., Bidanda, B., and Gulsen, M., 2000, "A model for the development, assessment, and validation of activity based costing systems for small manufacturers," Engineering Management Journal, no.1, pp. 31-38.

Needy, K.L., and Bidanda, B., 2000, "Production Flow Strategies," in Maynard Industrial Engineering Handbook, K. Zandin, ed., McGraw Hill.

Norman, B.A., Tharmmaphornphilas, W., Needy, K.L., Bidanda, B., and Warner, R.C., 2000, "Assigning workers to tasks considering technical and human skills," 9th Industrial Engineering Research Conference, Cleveland, OH.

Rafe, G., Needy, K.L., and Bidanda, B., 2000, "Motivations for a distributed virtual laboratory for continuous manufacturing education and training," 2000 American Society for Engineering Education Annual Conference, St. Louis, MO.

Bidanda, B., and Needy, K.L., 1999, "Development of an activity based costing system in your small company," Industrial Engineering Solutions '99 Conference, pp. 58-63, Phoenix, AZ.

Bidanda, B., Colosimo, R.L., Warner, P.J., and Billo, R.E., 1999, "Project Management & Implementation of Cellular Manufacturing," in Handbook of Cellular Manufacturing Systems, S. Irani, ed., John Wiley & Sons.

Rafe, G., Needy, K.L., and Bidanda, B., 1999, "Motivations for a distributed virtual laboratory for continuous manufacturing education and training," American Society for Engineering Education Annual Conference, Charlotte, NC.

Bidanda, B., Kadidal, M., and Billo, R., 1998, "Development of an Intelligent Castability and Cost Estimation System," International Journal of Production Research, no.2, pp. 547-568.

Billo, R.E., and Bidanda, B., 1998, "Part Family Identification: The Role of Engineering Databases," in Group Technology & Cellular Manufacturing: State-Of-The-Art Synthesis of Research and Practice, Kluwer Academic Publishers.

Cohen, Y., Bidanda, B., and Billo, R., 1998, "Accelerating the Generation of Work Measurement Standards through Automatic Speech Recognition: A Laboratory Study," International Journal of Production Research, no.10, pp. 2701-2715.

Petri, K., Billo, R., and Bidanda, B., 1998, "A Neural Network Process Model for Abrasive Flow Machining Operations," Journal of Manufacturing Systems, no.1, pp. 52-64.

Aguwa, C.C., Bidanda, B., and Nnaji, B.O., 1997, "Shared Manufacturing in Developing Countries: An African Perspective," The Fourth Africa-USA International Conference on Manufacturing Technology, Pittsburgh.

Billo, R.E., Bidanda, B., and Adickes, M., 1997, "Performance Testing of Hand-Held Scanners for 2D Barcode Symbologies," Factory Automation & Integrated Manufacturing (FAIM) Conference, York, U.K..

Bidanda, B., and Billo, R., 1996, "Parametric Design and NC Code Generation of Countersink Cutting Tools," International Journal of Computer Integrated Manufacturing, no.2, pp. 105-112.

Berardi, M., and Bidanda, B., 1996, "A Non-traditional Economic Justification Model for Advanced Technologies," the 5th Industrial Engineering Research Conference, Minneapolis, Minnesota.

Billo, R., Bidanda, B., and Tate, D., 1996, "A Genetic Cluster Algorithm for the Machine Component Grouping Problem," Journal of Intelligent Manufacturing, no.3, pp. 1-13.

Billo, R., Bidanda, B., Cohen, Y., Fei, C.Y., and Petri, K.L., 1996, "Performance Standards and Testing of Two-Dimensional Bar Code Systems for Overhead Scanning," Journal of Manufacturing Systems, no.5, pp. 305-315.

Billo, R., Needy, K., and Bidanda, B., 1996, "Challenges Facing Information Technologies to Support World Class Manufacturing Practices," Computers In Industry, pp. 163-165.

Cleland, D., Bidanda, B., and Chung, C., 1996, "Human Issues in Technology Implementation - Part 2," Industrial Management, no.5, pp. 15-16.

Cohen, Y., Bidanda, B., Billo, R.E., and Zandin, K.B., 1996, "On Integrating Work Measurement Systems with Voice Recognition Technologies," the 5th Industrial Engineering Research Conference, Minneapolis, Minnesota.

Cohen, Y., and Bidanda, B., 1996, "A Discrete Control Modeling Technique for Automated Industrial Systems," the Embedded Computing Conference, Paris.

Maitra, A., Bidanda, B., and Rubinovitz, J., 1996, "Need for the Development of a Generic Programming Interface for Industrial Robots," the SPIE Conference, pp. 89-95.

Wilhelm, M., Smith, A.E., and Bidanda, B., 1996, "Integrating an Expert System and a Neural Network for Process Planning," Engineering Design and Automation, no.4, pp. 259-269.

Wilhelm, M., Smith, A.E., and Bidanda, B., 1996, "Process Planning Using an Integrated Expert System and Neural Network Approach," in Hybrid Intelligent Systems Applications, J. Liebowitz, ed., Cognizant Communications/ISIS, pp. 3-23.

Bidanda, B., and Billo, R., 1995, "On the Use of Students for Developing Engineering Laboratories," Journal of Engineering Education, no.2, pp. 205-212.

Bidanda, B., and Billo, R.E., 1995, "On the Development of an Intelligent Speech-Based Work Measurement System," the 5th International FAIM Conference, Stuttgart, Germany.

Bidanda, B., and Needy, K.L., 1995, "Activity Based Costing for Small Manufacturers," the Fourth I.E. Research Conference, Nashville, TN.

Bidanda, B., Billo, R.E., and Cohen, Y., 1995, "A New Generation of Two Dimensional Bar Code Symbologies," the 13th International Conference on Production Research, Jerusalem.

Billo, R., and Bidanda, B., 1995, "Representing group technology classification and coding techniques with object oriented modeling," IIE Transactions, pp. 542-554.

Billo, R.E., Bidanda, B., and Kharbanda, P., 1995, "Re-Engineering Process Plans for Manufacturing Cell Design: A Case Study," the 13th International Conference on Production Research, Jerusalem.

Billo, R.E., and Bidanda, B., 1995, "Testing of Two-Dimensional Bar Code Systems for Overhead Sortation and Tracking," the Fourth I.E. Research Conference, Nashville, TN.

Burns, G., and Bidanda, B., 1995, "Modular Hierarchical Control Networks for the Specification and Implementation of Automated Manufacturing Control Systems," the Fourth I.E. Research Conference, Nashville, TN.

Cleland, D.I., Bidanda, B., and Chung, C., 1995, "Human Issues in Technology Implementation - Part 1," Industrial Management, no.4, pp. 22-27.

Cohen, Y., and Bidanda, B., 1995, "A New Generation of Work Measurement Systems for Manufacturing & Industrial Applications," the 13th International Conference on Production Research, Jerusalem.

Petri, K.L., Billo, R.E., and Bidanda, B., 1995, "The Development of Non-traditional Process Models for Extrusion Honing," the Fourth I.E. Research Conference, Nashville, TN.

Bidanda, B., and Hosni, Y., 1994, "Reverse Engineering and its Relevance to Industrial Engineering: A Critical Overview," Computers and Industrial Engineering Journal, no.2, pp. 343-348.

Bidanda, B., Narayanan, V., and Billo, R., 1994, "Reverse Engineering & Rapid Prototyping," in Handbook of Automation and Manufacturing Systems, R.C. Dorf, and A. Kusiak, eds., John Wiley & Sons.

Billo, R., Bidanda, B., and Kharbanda, P., 1994, "Re-Engineering Process Plans for Effective Manufacturing Cell Formation," International Journal of Manufacturing Systems Design, no.3, pp. 217-229.

Billo, R., Bidanda, B., and Peternel, J., 1994, "Enhancing Classification and Coding Techniques with Object Oriented Modeling for Group Technology Applications," the Third I.E. Research Conference, pp. 549-554, Atlanta, GA.

Billo, R., Bidanda, B., and Tate, D., 1994, "A Genetic Algorithm Formulation of the Cell Formation Problem," 16th Int. Conference on Computers and Industrial Engineering, Ashikaga, Japan.

Billo, R., and Bidanda, B., 1994, "A Student Advising System for Undergraduate Engineering Curricular Scheduling," Computers in Education, no.3, pp. 205-213.

Burns, G., and Bidanda, B., 1994, "An Iconic Programming System for Flexible Control of Automated Systems," ISRAM 1994, Maui.

Burns, G., and Bidanda, B., 1994, "An Integrated Petri Net Environment for Analysis and Logic Control of Manufacturing Systems," the Third I.E. Research Conference, Atlanta, GA.

Burns, G., and Bidanda, B., 1994, "The Use of Hierarchical Petri Nets for the Automatic Generation of Ladder Logic Programs," the ESD/IPC' 94 Conference & Exposition, pp. 169-179, Detroit, MI.

Dharwadkar, S., Bidanda, B., and Cleland, D., 1994, "Shared Manufacturing Assistance Center Project: A New Product Development," in THE GLOBAL PROJECT MANAGEMENT HANDBOOK, D. Cleland, and R. Gareis, eds., McGraw Hill.

Motavalli, S., and Bidanda, B., 1994, "Modular Software Development for Digitizing Data Analysis in Reverse Engineering," Computers and Industrial Engineering Journal, no.2, pp. 395-410.

Redfern, M., and Bidanda, B., 1994, "Slip Resistance of the Shoe-Floor Interface Under Bio-mechanically Relevant Conditions," Ergonomics, no.3, pp. 511-524.

Sergio, B., Smith, A., and Bidanda, B., 1994, "Reducing Waste in Casting with a Predictive Neural Model," Journal of Intelligent Manufacturing, pp. 277-286.

Bidanda, B., Billo, R., and Peternel, J., 1993, "Computer Aided Feature Based Design and NC Code Generation of Countersink Tools," the FAIM 1993 Conference, CRC Press, pp. 245-254, Limerick, Ireland.

Bidanda, B., Cleland, D., and Dharwadkar, S., 1993, "Shared Manufacturing: An Approach to Global Competitiveness," the FAIM 1993 Conference, CRC Press, pp. 55-66, Limerick, Ireland.

Bidanda, B., Cleland, D.I., and Dharwadkar, S., 1993, "SHARED MANUFACTURING SYSTEMS: A GLOBAL PERSPECTIVE," McGraw-Hill Book Company, New York.

Bidanda, B., Cohen, P.H., and Tunasar, C., 1993, "FIXPERT: A Rule Based System for Workholding Device Selection of Rotational Parts," in EXPERT SYSTEMS IN PRODUCTION & MANUFACTURE: STRUCTURE AND RULES, S. Anand, and A. Mital, eds., Chapman and Hall.

Bidanda, B., Rubinovitz, J., and Narayanan, V., 1993, "CAD-Based Interactive Off-line Programming of Spray Glazing Robots," International Journal of Computer Integrated Manufacturing, no.6, pp. 357-365.

Ben-Brahim, S., Smith, A., and Bidanda, B., 1993, "Relating Product Specifications and Performance Data with a Neural Network Model for Design Improvement," Journal of Intelligent Manufacturing, pp. 367-374.

Billo, R.E., and Bidanda, B., 1993, "The Start Up of an Automated Data Collection Laboratory," 4th Annual Automatic Identification Educators Conference, Philadelphia.

Burns, G., Rajgopal, J., and Bidanda, B., 1993, "Integrating Group Technology and TSP for Scheduling Operations with Sequence Dependent Setup Times," the Second I.E. Research Conference, pp. 837-841, Los Angeles, CA.

Narayanan, V., Bidanda, B., and Rubinovitz, J., 1993, "Off-Line Programming and Path Planning of Spray Glazing Robots," the XIII International Conference for Production Research (ICPR), Elsevier Science Publishers.

Rajgopal, J., and Bidanda, B., 1993, "On the Use of Statistical Design in Manufacturing Engineering Education," International Journal of Applied Engineering Education, no.4.

Smith, A., Martinez, S., and Bidanda, B., 1993, "A Neural Predictive Quality Model for Slip Casting Using Categorical Metrics," the Second I.E. Research Conference, pp. 265-269, Los Angeles, CA.

Bidanda, B., and Muralikrishnan, C.K., 1992, "Flexible Fixtures for Intelligent Manufacturing," in Intelligent Design and Manufacturing, A. Kusiak, ed., John Wiley & Sons.

Bidanda, B., Shuman, L., and Puerzer, R., 1992, "On Teaching CAD Concepts to Industrial Engineers," Engineering Design Graphics Journal, no.2, pp. 11-18.

Ben-Brahim, S., Smith, A., and Bidanda, B., 1992, "Estimating Product Performance and Quality from Design Parameters Via Neural Networks," the First I.E. Research Conference, Chicago, IL.

Cleland, D., Bidanda, B., and Dharwadkar, S., 1992, "A Shared Manufacturing Assistance Center Project," the Project Management Institute Seminar & Symposium, pp. 466-473, Pittsburgh, PA.

Motavalli, S., and Bidanda, B., 1992, "Modular Software Development for Reverse Engineering Applications," the First I.E. Research Conference, Chicago, IL.

Narayanan, V., Rubinovitz, J., and Bidanda, B., 1992, "On the Development of Computer Based Path Planning Strategies for Robotic Spray Glazing," Computers and Industrial Engineering Journal, pp. 15-18.

Bidanda, B., Motavalli, S., and Harding, K., 1991, "Reverse Engineering: An Evaluation of Prospective Non-Contact Technologies and Applications in Manufacturing Systems," International Journal of Computer Integrated Manufacturing, no.3, pp. 145-156.

Bidanda, B., Rubinovitz, J., and Narayanan, V., 1991, "Off-line Programming for Robotic Spray Glazing Cell," Fourth World Conference on Robotics Research, Pittsburgh, PA.

Bidanda, B., Shuman, L., and Puerzer, R., 1991, "On Teaching CAD Concepts to Industrial Engineers," the ASEE Conference, New Orleans.

Motavalli, S., and Bidanda, B., 1991, "Development of a Part Image Reconstruction System for Reverse Engineering of Design Modifications," Journal of Manufacturing Systems, no.5.

Rajgopal, J., and Bidanda, B., 1991, "On Scheduling Parallel Machines with Two Setup Classes," International Journal of Production Research, no.12, pp. 2443-2458.

Redfern, M., and Bidanda, B., 1991, "Programmable Shoe/Floor Tester to Evaluate Floor Slipperiness," in ADVANCES IN INDUSTRIAL ERGONOMICS AND SAFETY III, W. Karwowski, and J.W. Yates, eds., Taylor & Francis.

Bidanda, B., and Cleland, D.I., 1990, "THE AUTOMATED FACTORY HANDBOOK: TECHNOLOGY AND MANAGEMENT," Tab Professional and Reference Books, Blue Ridge Summit, PA.

Bidanda, B., and Motavalli, S., 1990, "On the Applications of Part Image Reconstruction Systems in Automated Manufacturing," 5th International conference on CAD/CAM, Robotics and Factories of the Future, Elsevier Science Publishers, Norfolk, Virginia.

Bidanda, B., and Rajgopal, J., 1990, "Optimal Selection of Workholding Devices for Rotational Parts," IIE Transactions, no.1.

Bidanda, B., Motavalli, S., and Patterson, G.P., 1990, "On the Development of a Computerized System for Cephalometric Analysis," Journal of Medical Systems, no.1.

Burhanuddin, S., and Bidanda, B., 1990, "Industrial Robots," in THE AUTOMATED FACTORY HANDBOOK; TECHNOLOGY AND MANAGEMENT, B. Bidanda, and D.I. Cleland, eds., Tab Professional and Reference Books (Division of McGraw-Hill), Blue Ridge Summit, PA.

Bidanda, B., and Cleland, D., 1989, "Techniques to Assess Project Feasibility," Project Management Journal, no.2.

Bidanda, B., and Motavalli, S., 1989, "Reverse Engineering using Structured Lighting," 4th International Conference on CAD/CAM, Robotics and Factories of the Future, Elsevier Science Publishers, Delhi, India.

Bidanda, B., Rubinovitz, J., and Raman, S., 1989, "Development of a Spatter Index for Automated Welding Inspection Using Computer Vision," Computers in Industrial Engineering Journal, no.2, pp. 215-224.

Knott, K., Bidanda, B., and Pennebaker, D., 1988, "The Economics of Robotic Welding," The International Journal of Production Research, no.1.

Bidanda, B., and Knott, K., 1987, "Roadblocks to Robotic Welding," Journal of Methods-Time Measurement.

Bidanda, B., "Designing and Implementing Large Scale Cellular Manufacturing Systems," Banff.

Bidanda, B., "Designing and Implementing Large Scale Cellular Manufacturing Systems," IIE Solutions Conference, Banff.

Bidanda, B., and Cohen, P.H., "An Integrated CAD-CAM Approach for the Selection of Workholding Devices for Concentric, Rotational Components," 14th conference of the NSF Production Research and Technology Program, Society of Manufacturing Engineers, Dearborn, MI.

Bidanda, B., and Cohen, P.H., "Automated Fixture Selection for Rotational Parts," 3rd International Conference for CAD/CAM and Robotics, Elsevier Science Publishers.

Bidanda, B., and Cohen, P.H., "Development of a Computer Aided Fixture Selection System for Concentric, Rotational Parts," Symposium on Advances in Integrated Product Design and Manufacturing, pp. 219-226.

Bidanda, B., and Motavalli, S., "Building CAD Models with Non-Contact Techniques," IIE Conference, Atlanta, GA.

Bidanda, B., and Rubinovitz, J., "Use of a Computer Vision System to check for Spatter in Butt Welds," 22nd SES Annual Meeting.

Bidanda, B., and Wolfe, H., "An Analysis for Manufacturing System Laboratory Development," ASEE Conference, pp. 303-307, Portland, OR.

Bidanda, B., Cohen, P.H., and Schmidt, A.O., "Cellular Manufacturing for Small Shops," International Conference on Technology and Technology Exchange-ICTTE 1986.

Bidanda, B., Colosimo, R., and Petri, K., "On Improving Manufacturing Efficiency," the International Conference on Manufacturing Excellence: Mexcel 95, Bangalore, India.

Bidanda, B., Di Pasquale, J., Clune, J., and Creehan, K., "Rapid Prototyping & Reverse Engineering Applications in a BioMedical Environment," International Conference of Production Research, Limerick, Ireland.

Bidanda, B., Narayanan, V., Brahim, B.S., and Thorne, J., "On the Development of a Robotic Work Cell for Sanitary Ware Spray Glazing," XIII Conference in Computers and Industrial Engineering, Orlando, Florida.

Bidanda, B., Rajgopal, J., and Shuman, L., "Flexible Doctoral Programs for International Faculty," International Conference for Engineering Education, Rio de Janerio.

Bidanda, B., Sepideh, A., Shankar, M.R., and Basu, S., "Sustainable Design and Manufacturing by Mapping, Microstructure from Severe Shear Deformation in Machining," 14th IFAC Symposium on Information Control Problems in Manufacturing, Bucharest.

Billo, R., Bidanda, B., and Peternel, J., "Parametric Design of Countersink Cutting Tools," the Second I.E. Research Conference, pp. 370-374, Los Angeles, CA.

Billo, R., Tate, D., and Bidanda, B., "Comparison of a Genetic Algorithm and Cluster Analysis for the Cell Formation Problem: A Case Study," the Third I.E. Research Conference, pp. 543-548, Atlanta, GA.

Billo, R.E., and Bidanda, B., "How to Implement ADC," the Automatic Identification & Data Capture Seminar, Pittsburgh, PA.

Billo, R.E., and Bidanda, B., "Modeling Effective Material Tracking Systems: A Case Study in Wireless Technology," Banff.

Cohen, Y., and Bidanda, B., "Y- Nets for Automated Production," the International Conference for Production Research (ICPR), Osaka.

Cohen, Y., and Bidanda, B., "Y-Nets: A New Technique for Modeling Discrete Control in Industrial Systems," the Sixth Industrial Engineering Research Conference, pp. 586-591, Miami Beach.

Colosimo, R., Needy, K., and Bidanda, B., "Worker Assignments in Implementing Manufacturing Cells," the Sixth Industrial Engineering Research Conference, pp. 240-245, Miami Beach.

Kadidal, M., and Bidanda, B., "A Castability Expert System," XV Conference in Computers and Industrial Engineering, Florida.

Narayanan, V., and Bidanda, B., "Analysis of Process Parameters for Robotic Spray Glazing," the Fourth I.E. Research Conference, Nashville, TN.

Rajgopal, J., Bidanda, B., and Shuman, L., "Flexible Doctoral Programs for International Faculty," International Conference on Engineering Education, Rio de Janerio.


http://www.engineering.pitt.edu/People/Faculty/SSOE/Active/Bidanda,-Bopaya/

Tuesday, May 12, 2015

Supply Chain Industrial Engineering - Online Book


Supply Chain Industrial Engineering - Explanation


Supply chain industrial engineering is the study of resource use in various supply chain activities with a view to increasing the efficiency or eliminating the waste wherever possible. While the supply chain is designed to serve the needs of the targeted customers, the resource use in the design is carefully investigated by the industrial engineering to identify and remove waste. Industrial engineering succeeded in reducing the cost of many processes designed in the first iteration by the managers up to 50% and hence it is a very important activity in systems design or systems engineering.

Famous example of industrial engineering, is Henry Ford's production system redesign, that reduced the price of the automobile by half.

System Industrial Engineering - System Human Effort Engineering - System Efficiency Engineering


Supply Chain Engineering


 We define "Supply Chain Engineering" as the application of scientific principles to optimize the design and integration of supply chain processes, infrastructure, technology and strategy.(Supply Chain and Logistics Institute at Georgia Tech.)
http://www.scl.gatech.edu/about.php


IE 497 –Supply Chain Engineering
Fall Semester 2012
Course at Penn State University


Course Objective
This course is designed to provide students with a quantitative background for designing, analyzing,
managing, and improving supply chains.

The Chopra & Meindl textbook (prescribed text for the course) is targeted to business students and so it will be supplemented with appropriate
quantitative models.
http://www2.ie.psu.edu/griffin/sc_syllabus.pdf



__________

Supply Chain Industrial Engineers

Scott J. Edwards, Intel Corporation

Scott is an Industrial Engineer in the Supply Chain Industrial Engineering and Statistics department at Intel Corporation. His professional experience includes process improvement, capacity planning and modeling, and network design in logistics/supply chain areas. Scott has a Bachelor of Science degree in Industrial and Management Systems Engineering from Arizona State University and a Masters degree in Business Administration from the University of Phoenix. He is also a certified Six Sigma Black Belt through Arizona State University’s Ira A. Fulton School of Engineering and received his “Jonah” recognition from Washington State University / TOCICO.

http://www.cpi-symposiums.com/speakers.html
Interesting Presentation by Scott Edwards
http://www.pinnacle-strategies.com/articles/CPI%20Intel%20TOC%20Lean%20Six%20Sigma%20May%202008.pdf


Patrick O'Gorman
Senior Supply Chain Industrial Engineer
Siltronic AG
Public Company; 5001-10,000 employees; Semiconductors industry
March 2009 – September 2012 (3 years 7 months)

Deputy for Supply Chain Management role.
Global capacity / load / utilization analysis and modeling.
Design, implement and improve on manufacturing support systems.
Global inventory reporting.
Revenue forecasting.
Lead and work on cross-functional project teams.
Global Lean Supply Chain initiatives.
SAP/R3 Master Data maintenance and analysis.
Product / Unit / Lot genealogy migration.
Analyze and recommend efficiency and productivity improvements.
Design, implement, and optimize material flow control systems.
Overall Equipment Effectiveness (OEE) - Program development.
Advanced material mix balancing, optimization and maintenance within gemba.
Overall Operator Effectiveness (OOE) - Program development.
Global process and procedure development.
Provide technical expertise to define line equipment layouts and equipment interfaces for material handling/control and overall equipment utilization.
Prepare capital proposals.
Lead and facilitate cross-functional training.
Maintain appropriate documentation for material flow and control systems.
Determine impact on material flow and line balance of process changes, material flow changes, yield enhancements and equipment efficiencies.
KPI & Business Intelligence design.
Global Supply Chain Industrial Engineering team member.
Design planning and scheduling systems to optimize manufacturing systems.
Patrick has 7 recommendations (1 manager, 3 co-workers, 3 partners) including:
3rd Jordan H., MIM Degree Candidate, Portland State University
3rd Chase J., student, Portland State University
Supply Chain Industrial Engineer
Siltronic AG
Public Company; 5001-10,000 employees; Semiconductors industry
March 2007 – March 2009 (2 years 1 month)

Deputy for Operations Management role.
Estimate and update equipment capacities and process standards.
Provide material flow system training to operations.
Design workstations and material fixtures to improve productivity and safety.
Global facility benchmarking.
Analyze manufacturing systems and equipment for performance; inventory level, cycle times, scheduling, utilization and capacity.
Work across functional lines with operations, equipment engineering, and process technology.
Analyze and recommend proposals for changing manufacturing systems.
Data mining.
Support operations, logistics and engineering in daily decision making process regarding flow system problem solving.
Analyze equipment needs and material flow control systems to recommend purchase and layout requirements to enhance systems that improve cycle time, inventory and efficiency.

http://www.linkedin.com/in/globalcitizenpatrickogorman

__________
__________

Human Effort Engineering - Techniques

1. Principles of Motion Economy
2. Motion Study
3. Workstation Design
4. Application of Ergonomics and Biomechanics
5. Fatigue Studies
6. Productivity/Safety/Comfort Device Design
7. Standardization of  Methods
8. Operator training
9. Incentive Systems
10. Job Evaluation
11. Learning effect capture
12. Work Measurement


EFFICIENCY IMPROVEMENT TECHNIQUES OF INDUSTRIAL ENGINEERING


1. Process Analysis
2. Operation Analysis
3. Layout Efficiency Analysis
4. Value engineering
5. Statistical quality control
6. Statistical inventory control and ABC Classification Based Inventory Sytems
7. Six sigma
8. Operations research
9. Variety reduction
10. Standardization
11. Incentive schemes
12. Waste reduction or elimination
13. Activity based management
14. Business process improvement
15. Fatigue analysis and reduction
16. Engineering economy analysis
17. Learning effect capture and continuous improvement (Kaizen, Quality circles and suggestion schemes)
18. Standard costing


Functional Solutions

1.Warehouse efficiency improvement
2. Warehouse 5S
3. Warehouse human effort engineering
4. Inventory control




Supply Chain Human Effort Engineering - Techniques


1. Principles of Motion Economy

2. Motion Study
    Wearable computers empower workers to achieve new levels of efficiency in package handling and warehouse applications.
     http://www.mmh.com/article/wearable_computers_optimize_workflows
     MMH - Modern Material Handling Magazine website

3. Workstation Design

4. Application of Ergonomics and Biomechanics
    Warehouse workers - Take the hurt out of material handling
     http://www.cdph.ca.gov/programs/hesis/Documents/warehous.pdf

5. Fatigue Studies

6. Productivity/Safety/Comfort Device Design

7. Standardization of  Methods

8. Operator training

9. Incentive Systems

10. Job Evaluation

11. Learning effect capture

12. Work Measurement


SUPPLY CHAIN SYSTEM EFFICIENCY IMPROVEMENT



1. Process Analysis
    A Better, Easier Way to Improve Warehouse Operations
    12 Leading case studies
     Steve Anderson, Acorn Systems Inc., 2004
     Request white paper from Acorn Systems

2. Operation Analysis

3. Layout Efficiency Analysis

4. Value engineering

5. Application of Statistics in Supply Chain Planning, Control and Operations


    Forecasting

    Forecasting supply chain components with time series analysis
    Electronic Components and Technology Conference, 2003. Proceedings.
    Date of Conference: May 27-30, 2003
    Author(s): Martin, L.J. and Frei, J. ,  Page(s): 269 278

    Statistical quality control

    Statistical inventory control and ABC Classification Based Inventory Systems

    Supply Chain Risk Management
    ftp://ftp.software.ibm.com/common/ssi/sa/wh/n/gbw03015usen/GBW03015USEN.PDF
    Six sigma

    54 statistics on hospital supply chain (efficiency)
    http://www.beckershospitalreview.com/racs-/-icd-9-/-icd-10/54-statistics-on-hospital-supply-chain-efficiency.html

    Supply Chain Monitoring: A Statistics Approach
    Fernando D. Mele, Estanislao Musulin and Luis Puigjaner*
    European Symposium on Computer Aided Process Engineering – 15
    L. Puigjaner and A. Espuña (Editors)
    2005 Elsevier Science B.V.

    Forecasting in Supply Chain
    http://logistics.about.com/od/strategicsupplychain/a/Forecasting.htm



6. Optimization and Operations research

     IBN ILOG
     http://www-01.ibm.com/software/websphere/products/sca/

      http://www.ups.com/content/us/en/bussol/browse/supply-chain-optimization.html

     http://www.scl.gatech.edu/research/supply-chain/10rules.pdf
 

7. Variety reduction

     Measuring variety reduction along the supply chain: The Variety Gap Model
     by: Alessandro Brun, Margherita Pero, International Journal of Production Economics (May 2012)

     Variety Management in assemble-to-order supply chains
     http://mpra.ub.uni-muenchen.de/5250/1/MPRA_paper_5250.pdf

8. Standardization

9. Waste reduction or elimination

     7 Wastes Supply Chain
     http://supplychain-mechanic.com/?p=75

     Lean Supply Chain Practices in Malaysia
     http://cdn.intechopen.com/pdfs/17141/InTech-Lean_supply_chain_practices_and_performance_in_the_context_of_malaysia.pdf

10. Activity based management - Supply Chain Cost Management using Activity Based Cost Measurement and Management

11. Business process improvement

12. Engineering economy analysis

13. Learning effect capture and continuous improvement (Kaizen, Quality circles and suggestion schemes)

14. Standard costing and Kaizen costing

15. Lean Warehousing

Webinar
___________________

___________________


Importance of Effectiveness - Only Effective Supply Chains are to be made efficient

The Triple A Supply Chain - Agile, Adaptive and Aligned
http://hbr.org/2004/10/the-triple-a-supply-chain/ar/1



Supply Chain Efficiency - Supply Chain Waste Elimination - Lean Supply Chain
Supply Chain Industrial Engineering - Bibliography




A Computational Model for Warehouse Analysis and Design
Karathur, Karthik N; Govindaraj, T; Bodner, Douglas A; McGinnis, Leon F. IIE Annual Conference. Proceedings (2002): 1-6.



Supply Chain Engineering Books


__________________________


Supply Chain Network Design: Applying Optimization and Analytics to the Global Supply Chain


Michael Watson, Sara Lewis, Peter Cacioppi, Jay Jayaraman
Publisher:  FT Press, Copyright:  2013
Format:  Cloth; 432 pp, Published:  08/22/2012


Table of Contents


Preface     xvi
Part I: Introduction and Basic Building Blocks
Chapter 1: THE VALUE OF SUPPLY CHAIN NETWORK DESIGN     1
Chapter 2: INTUITION BUILDING WITH CENTER OF GRAVITY MODELS     23
Chapter 3: LOCATING FACILITIES USING A DISTANCE-BASED APPROACH     37
Chapter 4: ALTERNATIVE SERVICE LEVELS AND SENSITIVITY ANALYSIS     63
Chapter 5: ADDING CAPACITY TO THE MODEL     83
Part II: Adding Costs to Two-Echelon Supply Chains
Chapter 6: ADDING OUTBOUND TRANSPORTATION TO THE MODEL     99
Chapter 7: INTRODUCING FACILITY FIXED AND VARIABLE COSTS     127
Chapter 8: BASELINES AND OPTIMAL BASELINES     139
Part III: Advanced Modeling and Expanding to Multiple Echelons
Chapter 9: THREE-ECHELON SUPPLY CHAIN MODELING     157
Chapter 10: ADDING MULTIPLE PRODUCTS AND MULTISITE PRODUCTION SOURCING     177
Chapter 11: MULTI-OBJECTIVE OPTIMIZATION     207
Part IV: How to Get Industrial-Strength Results
Chapter 12: THE ART OF MODELING     217
Chapter 13: DATA AGGREGATION IN NETWORK DESIGN     237
Chapter 14: CREATING A GROUP AND RUNNING A PROJECT     261
Part V: Case Study Wrap Up
Chapter 15: CASE STUDY: JPMS CHEMICALS CASE STUDY     277
Index     295

http://www.pearsonhighered.com/educator/product/Supply-Chain-Network-Design-Applying-Optimization-and-Analytics-to-the-Global-Supply-Chain/9780133017373.page





Supply Chain Engineering: Models and Applications


By A. Ravi Ravindran, Donald Warsing, Jr.

Published September 27th 2012 by CRC Press – 548 pages


Table of Contents

Introduction to Supply Chain Engineering

Understanding Supply Chains

Flows in Supply Chains

Meaning of Supply Chain Engineering

Supply Chain Decisions

Enablers and Drivers of Supply Chain Performance

Assessing and Managing Supply Chain Performance

Relationship between Supply Chain and Financial Metrics

Importance of Supply Chain Management

Organization of the Textbook

Summary and Further Readings

Exercises

References


Planning Production in Supply Chains

Role of Demand Forecasting in Supply Chain Management

Forecasting Process

Qualitative Forecasting Methods

Quantitative Forecasting Methods

Incorporating Seasonality in Forecasting

Incorporating Trend in Forecasting

Incorporating Seasonality and Trend in Forecasting

Forecasting for Multiple Periods

Forecasting Errors

Monitoring Forecast Accuracy

Forecasting Software

Forecasting in Practice

Production Planning Process

Aggregate Planning Problem

Linear Programming Model for Aggregate Planning

Nonlinear Programming Model for Aggregate Planning

Aggregate Planning as a Transportation Problem

Aggregate Planning Strategies: A Comparison

Summary and Further Readings

Replenishment (CPFR)

Exercises

References


Inventory Management Methods and Models

Decision Framework for Inventory Management

Some Preliminary Modeling Issues

Single-Item, Single-Period Problem: The Newsvendor

Single-Item, Multi-Period Problems

Multi-Item Inventory Models

Multi-Echelon Inventory Systems

Conclusions

Further Readings

A Appendix: The Bullwhip Effect

References

Exercises

References


Transportation Decisions in Supply Chain Management

Introduction

Motor Carrier Freight: Truckload Mode

Accounting for Goods in transit

Stepping Back: Freight Transportation Overview

More General Models of Freight Rates

Building A Rate Model: LTL Service

A More General Rate Model for LTL Service

Beyond Truck Transport: Rail and Air Cargo

Conclusion

Further Readings

Exercises

References


Location and Distribution Decisions in Supply Chains

Modeling with Binary Variables

Supply Chain Network Optimization

Risk Pooling or Inventory Consolidation

Continuous Location Models

Real-World Applications

Summary and Further Readings

Exercises

References


Supplier Selection Models and Methods

Supplier Selection Problem

Supplier Selection Methods

Multi-Criteria Ranking Methods for Supplier Selection

Multi-Objective Supplier Allocation Model

Summary and Further Readings

Exercises

References


Managing Risks in Supply Chain

Supply Chain Risk

Real World Risk Events and Their Impacts

Sources of Supply Chain Risks

Risk Identification

Risk Assessment

Risk Management

Best Industry Practices in Risk Management

Risk Quantification Models

Value-at-Risk (VaR) Models

Miss-the-Target (MtT) Risk Models

Risk Measures

Combining VaR and MtT Type Risks

Risk Detectability and Risk Recovery

Multiple Criteria Optimization Models for Supplier Selection Incorporating Risk

Summary and Further Readings

Exercises

Acknowledgments

References


Global Supply Chain Management

History of Globalization

Impacts of Globalization

Global Sourcing

International Logistics

Designing a Resilient Global Supply Chain: A Case Study

Summary and Further Readings

Exercises

Questions

References

Appendix A: Multiple Criteria Decision Making: An Overview

Index


http://www.routledge.com/books/details/9781439811986/

___________________________


Supply Chain Industrial Engineering - IIE Conference Papers






2
SUPPLY CHAIN MANAGEMENT PURCHASING/INVENTORY/MATERIALS (Presentation Supporting Paper)
Hamlin, Jerry; Migliore, R Henry, PhD; Paris, David; Metz, Rick D; Watt, David B. IIE Annual Conference. Proceedings (2002): 1-10.




5
Integration of Product Structure and Supply Chain Decisions at the Conceptual Design Stage: A Repository Enabled Decision Tool
Chiu, Ming-Chuan; Gupta, Saraj; Okudan, Gül E. IIE Annual Conference. Proceedings (2009): 1512-1517.

6
Object-oriented modeling of supply chain configuration problem
Chandra, Charu; Grabis, Janis. IIE Annual Conference. Proceedings (2006): 1-6.

7
 QUEUEING MODELS FOR ANALYZING SUPPLY CHAIN NETWORKS
Srivathsan, Sandeep; Krishnamoorthy, Ananth; Kamath, Manjunath; Ayodhiramanujan, Karthik. IIE Annual Conference. Proceedings (2004): 1-6.

8
 An Integrative Methodology for Product and Supply Chain Design Decisions at the Product Design Stage
Chiu, Ming-Chuan; Okudan, Gül. IIE Annual Conference. Proceedings (2010): 1-6.

9
 Supervisory Control of a Synchronized Supply Chain Using Petri Nets
Drzymalski, Julie; Odrey, Nicholas G. IIE Annual Conference. Proceedings (2010): 1-6.

10
 Supply Chain Risk Management
Hadavale, Rajesh S; Alexander, Suraj M. IIE Annual Conference. Proceedings (2009): 1363-1368.



12
 Modeling a Flexible Supply Chain and Logistics System Through Object-Oriented Approach
Kim, Jinho; Rogers, K J, PhD, PE. IIE Annual Conference. Proceedings (2003): 1-6.

13
 A Real-time Simulation-Based Control Architecture for Supply Chain Interactions
Ramakrishnan, Sreeram; Wysk, Richard A. IIE Annual Conference. Proceedings (2002): 1-6.

14
 A Rule Based Supply-Chain Business Model Under Object-Oriented Paradigm
Kim, Jinho; Rogers, K J, PhD, PE. IIE Annual Conference. Proceedings (2004): 1-6.

15
 Conflict and Cooperation of Scheduling in a Two-echelon Supply Chain
Chen, Yuerong; Li, Xueping. IIE Annual Conference. Proceedings (2009): 1357-1362.

16
 A Comparison of Coordinated Ordering Policies in a Three-Echelon Supply Chain Network
Abdelmaguid, Tamer F; Marzouk, Mohamed M. IIE Annual Conference. Proceedings (2009): 1239-1244.


17
 Inventory Accuracy Improvement via Cycle Counting in a Two-Echelon Supply Chain
Rossetti, Manuel D, PhD, PE; Gumrukcu, Seda; Buyurgan, Nebil; English, John. IIE Annual Conference. Proceedings (2007): 913-918.

18
 A MANUFACTURING STRATEGY FOR PRODUCT ASSEMBLY IN A SUPPLY CHAIN ENVIRONMENT
Sundaram, R Meenakshi; Patel, Rakesh B. IIE Annual Conference. Proceedings (2002): 1-8.

19
 Reducing Supply Chain Data Degradation in Emerging Networks
Ajoku, Pamela. IIE Annual Conference. Proceedings (2007): 180-185.

20
 The manager's guide to supply chain and logistics problem-solving tools and techniques: Part III: End user experiences
Hicks, Donald A. IIE Solutions29. 11 (Nov 1997): 34-38.

21
 Incomplete information equilibria: Separation theorems and other myths
Feldman, David. Annals of Operations Research151. 1 (Apr 2007): 119-149.




23
 The Effect of Information Update on Optimizing the Supply Chain Single Node Inventory Systems
Haji, Maryam; Darabi, Houshang. IIE Annual Conference. Proceedings (2006): 1-6.




26
 Emerging Supply Chain Drivers (Presentation)
Musselman, Ken. IIE Annual Conference. Proceedings (2002): 1-55.

27
 The Secrets of Supply Chain Success: A Retail Case Study (Presentation)
Anonymous. IIE Annual Conference. Proceedings (2004): 1-33.

28
 Reverse Logistics: Designing Your Supply Chain for Product Recovery (Presentation)
Barker, Theresa J; Zabinsky, Zelda B. IIE Annual Conference. Proceedings (2010): 1-18.

29
 Supply Chain Breakthrough Strategy: On-site MRO Partner-Managed Storeroom (Presentation)
Stein, Martin; Krauter, George. IIE Annual Conference. Proceedings (2009): 1-32.

30
 Driving Benefits from the Supply Chain: A Case Study (Presentation)
Miksis, Michael. IIE Annual Conference. Proceedings (2003): 1-18.

31
 Integrating Supply Chain Management and Maintenance Philosophies (Presentation)
Siriram, R; Cobb, P. IIE Annual Conference. Proceedings (2005): 1-43.

32
 Optimization Opportunities to Improve Supply Chain Efficiency: A Practitioner's Experiences (Presentation)
Saxena, Rajiv. IIE Annual Conference. Proceedings (2010): 1-22.



35
 It's all in the delivery
Anonymous. Industrial Engineer37. 1 (Jan 2005): 52.



36
 Managing Oil and Gas Supply Chain - Numerous Challenges, One Solution (Presentation)
Mehta, Arvind. IIE Annual Conference. Proceedings (2004): 1-14.

37
 Supply Chain Risk Management (Presentation)
Anonymous. IIE Annual Conference. Proceedings (2005): 1-21.

38
 Supply Chain Solution Using Six Sigma: A Case Study Based on a Project for Square D Company (Presentation)
Anonymous. IIE Annual Conference. Proceedings (2007): 1-19.

39
 Integrating Engineering for Supply Chain Effectiveness (Presentation)
Dickerson, James. IIE Annual Conference. Proceedings (2007): 1-24.

40
 Simulation of Supply Chain System Costs for Industrial Audiences (Presentation)
Ray, Charles D, Ph D. IIE Annual Conference. Proceedings (2005): 1-46.



43
 Designing principles to create resilient Supply Chains
Carvalho, Helena; Machado, V Cruz. IIE Annual Conference. Proceedings (2007): 186-191.






50
 Use of OR to Design Your Reverse Logistics Supply Chain (Presentation)
Barker, Theresa J; Zabinsky, Zelda B. IIE Annual Conference. Proceedings (2009): 1-25.
..."Use of OR to Design Your Reverse Logistics hitSupply Chain" during the Jun 01,

Citation/AbstractFull text - PDF (1 MB)‎
Save to My Research
Delete (Delete item 50)
51
 General Purpose Ontologies for Supply Chain Management
Ahmad, Ali; Mollaghasemi, Mansooreh; Rabelo, Luis. IIE Annual Conference. Proceedings (2004): 1-7.

 A methodology for the strategic design of robust global supply chains
Goetschalckx, Marc; Cordova, Gonzalo. IIE Annual Conference. Proceedings (2004): 1-6.

53
 Modeling and Mitigating Global Supply Chain Risk Management
Yang, Dengfeng; Wang, Jiao; Li, Xueping; Sawhney, Rapinder. IIE Annual Conference. Proceedings (2009): 1339-1344.

54
 AN INTERNET ENABLED SUPPLY CHAIN MANAGEMENT MODEL FOR SMALL AND MEDIUM SIZE ENTERPRISES
Magableh, Ghazi M; Abu-Ali, Mahmoud. IIE Annual Conference. Proceedings (2004): 1-6.

55
 Benefits of Incorporating Supply Chain Decisions into the Product Design via Design for Supply Chain
Gokhan, N Mehmet; Needy, Kim LaScola; Norman, Bryan A; Hunsaker, Brady. IIE Annual Conference. Proceedings (2008): 390-395.

56
 Supply Chain Reconfiguration: Designing Information Support With System Taxonomy Principles
Chandra, Charu; Tumanyan, Armen. IIE Annual Conference. Proceedings (2002): 1-6.


58
 An Improved Supplier Selection Method Integrated to the Conceptual Design Phase
Chiu, Ming-Chuan; Okudan, Gül. IIE Annual Conference. Proceedings (2009): 1518-1523.

59
 Supply chain system taxonomy: development and application
Chandra, Charu; Tumanyan, Armen. IIE Annual Conference. Proceedings (2003): 1-6.

60
 Taxonomy of Research Directions for Sustainable Supply Chain Management
Badurdeen, Fazleena; Metta, Haritha; Gupta, Sonal. IIE Annual Conference. Proceedings (2009): 1256-1261.

61
 Use of Shared Information in a Vendor-Managed Inventory (VMI) Supply Chain
Angulo, Andres; Nachtmann, Heather; Waller, Matthew. IIE Annual Conference. Proceedings (2002): 1-6.

62
 Combining Strategic and Tactical Decisions in an Integrated Supply Chain
Sajjadi, S Reza; Cheraghi, S Hossein. IIE Annual Conference. Proceedings (2009): 1149-1154.

63
 A Hybrid Solution Procedure for Design for Supply Chain Problems
Gokhan, N Mehmet; Needy, Kim LaScola; Norman, Bryan A; Hunsaker, Brady. IIE Annual Conference. Proceedings (2007): 1678-1683.

64
 Quantifying the Bullwhip Effect in the Supply Chain of Small-Sized Companies
Centeno, Martha A; Pérez, Jaime E. IIE Annual Conference. Proceedings (2009): 486-491.

65
 Supply Chain Models for Small Agricultural Enterprises
Jang, W; Klein, C M. IIE Annual Conference. Proceedings (2002): 1-6.


67
 Design for Supply Chain - A Collaborative Research Project Between Institutions and Between Centers
Needy, Kim L; Norman, Bryan A; Hunsaker, Brady; Gokhan, N Mehmet; Claypool, Erin; et al. IIE Annual Conference. Proceedings (2008): 396-401.


69
 Reverse Logistics Optimization with Data Envelopment Analysis
Tonanont, Ake; Yimsiri, Sanya; Rogers, K J. IIE Annual Conference. Proceedings (2009): 1268-1273.


71
 The Impact of the Internet Economy on Logistics
Sehwail, Loay; Ingalls, Ricki G. IIE Annual Conference. Proceedings (2005): 1-6.

 Applying Radio Frequency Identification for Cutting Tool Supply Chain Management
Cheng, Chen-Yang; Prabhu, Vittal. IIE Annual Conference. Proceedings (2007): 637-642.







78
 A Framework for Cost Modeling a Supply Chain
Yousef, Nabeel; Rabelo, Luis; Sepulveda, Jose. IIE Annual Conference. Proceedings (2006): 1-6.

79
 Stakeholder value mapping framework for supply chain improvement when implementing IT solutions
Alvarado, Karla P; Rabelo, Luis; Eaglin, Ronald. IIE Annual Conference. Proceedings (2008): 1320-1325.

80
 Simulation-Optimisation Methods in Supply Chain Applications: A Review
Abo-Hamad, Waleed; Arisha, Amr. Irish Journal of Management30. 2 (2011): 95-124.

81
 Goal-Driven Supply Chain Design
Chandra, Charu; Grabis, Janis. IIE Annual Conference. Proceedings (2008): 241-246.

82
 Elaborating Process Models for Supply Chain Reconfiguration
Chandra, Charu; Marukyan, Ruzanna. IIE Annual Conference. Proceedings (2002): 1-6.

83
 Integrated Supply Chain Management: Discrete Manufacturing (Presentation Supporting Paper)
Kumar, Dinesh. IIE Annual Conference. Proceedings (2002): 1-5.


85
 Information Modeling to Manage Supply Chain: Problems Taxonomy
Chandra, Charu; Tumanyan, Armen. IIE Annual Conference. Proceedings (2004): 1-6.

86
 Achieving Supply Chain Optimization: Guiding Your Organization's Improvement Journey (Presentation Supporting Paper)
Pinnekamp, Dale J, CPIM. IIE Annual Conference. Proceedings (2007): 1-7.

87
 Value Chain Management (VCM) Principles, Framework, and Footprint (Presentation)
Sabri, Ehap; Rehman, Aamer. IIE Annual Conference. Proceedings (2004): 1-22.


89
 Increased Supply Chain Efficiencies through Integration
Magableh, Ghazi M; Mason, Scott J. IIE Annual Conference. Proceedings (2003): 1-6.


91
 Optimization Strategies for Complex Supply Chains (Presentation)
Lathon, Ruby D, PhD. IIE Annual Conference. Proceedings (2006): 1-26.

92
 Applied Operational Research Techniques to Balance Costs & Service in Customers' Supply Chains (Presentation)
Jeray, Jim. IIE Annual Conference. Proceedings (2002): 1-37.

93
 A Maturity Model to Assess and Improve Supply Chain Operations
Giachetti, Ronald E; Garcia-Reyes, Heriberto. IIE Annual Conference. Proceedings (2010): 1-6.

94
 Collaborative implementation of e-business processes within the health-care supply chain: the Monash Pharmacy Project
Bhakoo, Vikram; Chan, Caroline. Supply Chain Management16. 3 (2011): 184-193.

95
 ANALYSIS OF A TRANSPORTATION CONTRACT IN A SUPPLY CHAIN
Sinha, Sudhir K; Rangaraj, N; Hemachandra, N. IIE Annual Conference. Proceedings (2006): 1-6.

96
 Considering Customer Waiting Time in Supply Chain Integration
Masel, Dale T; Pujari, Nikhil A. IIE Annual Conference. Proceedings (2005): 1-6.

97
 REDUCING PRODUCT DEVELOPMENT TIME USING CRITICAL CHAIN PROJECT MANAGEMENT TECHNIQUES (Presentation)
Ross, James. IIE Annual Conference. Proceedings (2003): 1-40.

98
 A Method for Measuring Supply Chain Interoperability
Ford, Thomas C, PhD; Ogden, Jeffrey A, PhD; Johnson, Alan W, PhD. IIE Annual Conference. Proceedings (2010): 1-6.

99
 Development of a Framework for Supply Chain Research in Industrial Engineering
Krishnamoorthy, Ananth; Kamath, Manjunath; Ingalls, Ricki G. IIE Annual Conference. Proceedings (2004): 1.

IE students and faculty can access these papers from Proquest Database


Industrial Engineering Faculty Members with focus on Supply Chain Industrial Engineering

http://comp.uark.edu/~mason/Research.html





Supply Chain Human Effort Engineering - Techniques

1. Principles of Motion Economy
 
2. Motion Study
    Wearable computers empower workers to achieve new levels of efficiency in package handling and warehouse applications.
     http://www.mmh.com/article/wearable_computers_optimize_workflows
     MMH - Modern Material Handling Magazine website

3. Workstation Design

4. Application of Ergonomics and Biomechanics
    Warehouse workers - Take the hurt out of material handling
     http://www.cdph.ca.gov/programs/hesis/Documents/warehous.pdf

5. Fatigue Studies

6. Productivity/Safety/Comfort Device Design

7. Standardization of  Methods

8. Operator training

9. Incentive Systems

10. Job Evaluation

11. Learning effect capture

12. Work Measurement


SUPPLY CHAIN SYSTEM EFFICIENCY IMPROVEMENT


1. Process Analysis
    A Better, Easier Way to Improve Warehouse Operations
    12 Leading case studies
     Steve Anderson, Acorn Systems Inc., 2004
     Request white paper from Acorn Systesm

2. Operation Analysis

3. Layout Efficiency Analysis

4. Value engineering

5. Application of Statistics in Supply Chain Planning, Control and Operations


    Forecasting

    Forecasting supply chain components with time series analysis
    Electronic Components and Technology Conference, 2003. Proceedings.
    Date of Conference: May 27-30, 2003
    Author(s): Martin, L.J. and Frei, J. ,  Page(s): 269 278

    Statistical quality control

    Statistical inventory control and ABC Classification Based Inventory Systems

    Supply Chain Risk Management
    ftp://ftp.software.ibm.com/common/ssi/sa/wh/n/gbw03015usen/GBW03015USEN.PDF
    Six sigma

    54 statistics on hospital supply chain (efficiency)
    http://www.beckershospitalreview.com/racs-/-icd-9-/-icd-10/54-statistics-on-hospital-supply-chain-efficiency.html

    Supply Chain Monitoring: A Statistics Approach
    Fernando D. Mele, Estanislao Musulin and Luis Puigjaner*
    European Symposium on Computer Aided Process Engineering – 15
    L. Puigjaner and A. Espuña (Editors)
    2005 Elsevier Science B.V.

    Forecasting in Supply Chain
    http://logistics.about.com/od/strategicsupplychain/a/Forecasting.htm

 

6. Optimization and Operations research

     IBN ILOG
     http://www-01.ibm.com/software/websphere/products/sca/

      http://www.ups.com/content/us/en/bussol/browse/supply-chain-optimization.html

     http://www.scl.gatech.edu/research/supply-chain/10rules.pdf
   

7. Variety reduction

     Measuring variety reduction along the supply chain: The Variety Gap Model
     by: Alessandro Brun, Margherita Pero, International Journal of Production Economics (May 2012)

     Variety Management in assemble-to-order supply chains
     http://mpra.ub.uni-muenchen.de/5250/1/MPRA_paper_5250.pdf

8. Standardization

9. Waste reduction or elimination

     7 Wastes Supply Chain
     http://supplychain-mechanic.com/?p=75

     Lean Supply Chain Practices in Malaysia
     http://cdn.intechopen.com/pdfs/17141/InTech-Lean_supply_chain_practices_and_performance_in_the_context_of_malaysia.pdf

10. Activity based management

11. Business process improvement

12. Engineering economy analysis

13. Learning effect capture and continuous improvement (Kaizen, Quality circles and suggestion schemes)

14. Standard costing and Kaizen costing


Importance of Effectiveness - Only Effective Supply Chains are to be made efficient

The Triple A Supply Chain - Agile, Adaptive and Aligned
http://hbr.org/2004/10/the-triple-a-supply-chain/ar/1



Books


Excellence in Inventory Management
Author: Stuart Emmett and David Granville
Edition: First
Publisher: Cambridge Academic
Date: 05/01/2007



Updated on 12 May 2015
First Published on 2 March 2013