Productivity orientation or cost reduction orientation in engineering design.
"In using engineering equipment, tools and other inputs to obtain the greatest economy and the most satisfactory results, the chief consideration has to be the maximum of work obtained from the cost spent on the equipment, tools and other inputs."
F.W. Taylor - Productivity Engineering of Belting - 1893 - Notes on Belting
Frederick Taylor's Productivity System for Rapidly Attaining The Maximum Productivity
Frederick Taylor's Piece Rate System for Rapidly Attaining The Maximum Productivity
The advantages of this system of management (Taylor's Piece Rate System) are :
The manufactures are produced cheaper under it.
The system is rapid in attaining the maximum productivity of each machine and man.
The system introduced by the writer, however, is directly the opposite, both in theory and in its results. It makes each workman’s interests the same as that of his employer, pays a premium for high efficiency, and soon convinces each man that it is for his permanent advantage to turn out each day the best quality and maximum quantity of work.
The writer has endeavored in the following pages to describe the system of management introduced by him in the works of the Midvale Steel Company, of Philadelphia, which has been employed by them during the past ten years with the most satisfactory results.
The system consists of three principal elements :
( i ) An elementary rate-fixing department.
( 2 ) The differential rate system of piece-work.
( 3 ) What he believes to be the best method of managing men who work by the day.
Elementary rate-fixing differs from other methods of making piece-work prices in that a careful study is made of the time required to do each of the many elementary operations into which the manufacturing of an establishment may be analyzed or divided. These elementary operations are then classified, recorded, and indexed, and when a piece-work price is wanted for work the job is first divided into its elementary operations, the time required to do each elementary operation is found from the records, and the total time for the job is summed up from these data. While this method seems complicated at the first glance, it is, in fact, far simpler and more effective than the old method of recording the time required to do whole jobs of work, and then, after looking over the records of similar jobs, guessing at the time required for any new piece of work.
The advantages of this system of management are :
First. That the manufactures are produced cheaper under it, while at the same time the workmen earn
higher wages than are usually paid.
Second . Since the rate-fixing is done from accurate knowledge instead of more or less by guess-work, the motive for holding back on work, or “ soldiering ”, and endeavoring to deceive the employers as to the time required to do work, is entirely removed, and with it the greatest cause for hard feelings and war between the management and the men.
Third. Since the basis from which piece-work as well as day rates are fixed is that of exact observation, instead of being founded upon accident or deception, as is too frequently the case under ordinary systems, the men are treated with greater uniformity and justice, and respond by doing more and better work.
Fourth, It is for the common interest of both the management and the men to cooperate in every way, so as to turn out each day the maximum quantity and best quality of work.
Fifth. The system is rapid, while other systems are slow, in attaining the maximum productivity of each machine and man ; and when this maximum is once reached, it is automatically maintained by the differential rate.
Sixth. It automatically selects and attracts the best men for each class of work, and it develops many first-class men who would otherwise remain slow or inaccurate, while at the same time it discourages and sifts out men who are incurably lazy or inferior.
Finally. One of the chief advantages derived from the above effects of the system is, that it promotes a most friendly feeling between the men and their employers, and so renders labor unions and strikes unnecessary.
39. The most formidable obstacle is the lack of knowledge on the part of both the men and the management (but chiefly the latter) of the quickest time in which each piece of work can be done; or, briefly, the lack of accurate time-tables for the work of the place.
40. The remedy for this trouble lies in the establishment in every factory of a proper rate-fixing department; a department which shall have equal dignity and command equal respect with the engineering and managing departments, which shall be organized and conducted in an equally scientific and practical manner.
41. The rate-fixing, as at present conducted, even in our best managed establishments, is very similar to the mechanical engineering of fifty or sixty years ago. Mechanical engineering at that time consisted in imitating machines which were in more or less successful use, or in guessing at the dimensions and strength of the parts of a new machine ; and as the parts broke down or gave out, in replacing them with the stronger ones. Thus each new machine presented a problem almost independent of former designs, and one which could only be solved by months or years of practical experience and a series of break-downs.
Modern engineering, however, has become a study, not of individual machines, but of the resistance of materials, the fundamental principles of mechanics, and of the elements of design.
44. Yet this elementary system of fixing rates has been in successful operation for the past ten years, on work complicated in its nature and covering almost as wide a range of variety as any manufacturing that the writer knows of. In 1883, while foreman of the machine shop of the Midvale Steel Company of Philadelphia, it occurred to the writer that it was simpler to time each of the elements of the various kinds of work done in the place, and then find the quickest time in which each job could be done, by summing up the total times of its component parts, than it was to search through the records of former jobs and guess at the proper price. After practising this method of rate-fixing himself for about a year as well as circumstances would permit, it became evident that the system was a success. The writer then established the rate-fixing department, which has given out piece-work prices in the place ever since.
45. This department far more than paid for itself from the very start ; but it was several years before the full benefits of the system were felt, owing to the fact that the best methods of making and recording time observations of work done by the men, as well as of determining the maximum capacity of each of the machines in the place, and of making working-tables and time-tables, were not at first adopted.
46. Before the best results were finally attained in the case of work done by metal-cutting tools, such as lathes, planers, boring mills, etc., a long and expensive series of experiments was made, to determine, formulate, and finally practically apply to each machine the law governing the proper cutting speed of tools, namely, the effect on the cutting speed of altering any one of the following variables : the shape of the tool (i.e., lip angle, clearance angle, and the line of the cutting edge), the duration of the cut, the quality or hardness of the metal being cut, the depth of the cut, and the thickness of the feed or shaving.
47. It is the writer’s opinion that a more complicated and difficult piece of rate-fixing could not be found than that of determining the proper price for doing all kinds of machine work on miscellaneous steel and iron castings and forgings, which vary in their chemical composition from the softest iron to the hardest tool steel. Yet this problem was solved through the rate-fixing department and the “ differential rate,” with the final result of completely harmonizing the men and the management, in place of the constant war that existed under the old system. At the same time the quality of the work was improved and the output of the machinery and the men was doubled, and in many cases trebled. At the start there was naturally great opposition to the ratefixing department, particularly to the man who was taking time observations of the various elements of the work ; but when the men found that the rates were fixed without regard to the records of the quickest time in which they had actually done each job, and that the knowledge of the department was more accurate than their own, the motive for hanging back or “ soldiering ” on this work ceased, and with it the greatest cause for antagonism and war between the men and the management
48. As an illustration of the great variety of work to which elementary rate-fixing has already been successfully applied, the writer would state that while acting as general manager of two large sulphite pulp mills he directed the application of piece-work to all of the complicated operations of manufacturing throughout one of these mills, by means of elementary rate-fixing, with the result, within eighteen months, of more than doubling the output of the mill.
The difference between elementary rate-fixing and the ordinary plan can perhaps be best explained by a simple illustration. Suppose the work to be planing a surface on a piece of cast iron. In the ordinary system the rate-fixer would look through his records of work done by the planing machine, until he found a piece of work as nearly as possible similar to the proposed job, and then guess at the time required to do the new piece of work. Under the elementary system, however, some such analysis as the following would be made
66. Of the two devices for increasing the output of a shop, the differential rate and the scientific rate-fixing department, the latter is by far the more important. The differential rate is invaluable at the start as a means of convincing men that the management is in earnest in its intention of paying a premium for hard work, and it at all times furnishes the best means of maintaining the top notch of production ; but when, through its application, the men and the management have come to appreciate the mutual benefit of harmonious cooperation and respect for each other’s rights, it ceases to be an absolute necessity. On the other hand, the rate-fixing department, for an establishment doing a large variety of work, becomes absolutely indispensable. The longer it is in operation the more necessary it becomes.
67. Practically, the greatest need felt in an establishment wishing to start a rate-fixing department is the lack of data as to the proper rate of speed at which work should be done.
There are hundreds of operations which are common to most large establishments ; yet each concern studies the speed problem for itself, and days of labor are wasted in what should be settled once for all and recorded in a form which is available to all manufacturers.
68. What is needed is a hand-book on the speed with which work can be done, similar to the elementary engineering hand-books. And the writer ventures to predict that such a book will, before long, be forthcoming. Such a book should describe the best method of making, recording, tabulating, and indexing time-observations, since much time and effort are wasted by the adoption of inferior methods.
69. The term “ rate-fixing department,” has rather a formidable sound. In fact, however, that department should consist in most establishments of one man, who in many cases need give only a part of his time to the work.
The careful study of the capabilities of the machines arid the analysis of the speeds at which they must run, before differential rates can be fixed which will insure their maximum output, almost invariably result in first indicating and then correcting the defects in their design and in the method of running and caring for them.
75. In the case of the Midvale Steel Company, to which I have already referred, the machine shop was equipped with standard tools furnished by the best makers, and the study of these machines, such as lathes, planers, boring mills, etc., which was made in fixing rates, developed the fact that they were none of them designed and speeded so as to cut steel to the best advantage. As a result, this company has demanded alterations from the standard in almost every machine which they have bought during the past eight years. They have themselves been obliged to superintend the design of many special tools which would not have been thought of had it not been for elementary rate-fixing.
76. But what is perhaps of more importance still, the rate-fixing department has shown the necessity of carefully systematizing all of the small details in the running of each shop, such as the care of belting, the proper shape for cutting tools, and the dressing, grinding, and issuing sairfe, oiling machines, issuing orders for work, obtaining accurate labor and material returns, and a host of other minor methods and processes. These details, which are usually regarded as of comparatively small importance, and many of which are left to the individual judgment of the foreman and workmen, are shown by the rate-fixing department to be of paramount importance in obtaining the maximum output, and to require the most careful and systematic study and attention in order to insure uniformity and a fair and equal chance for each workman. Without this preliminary study and systematizing of details it is impossible to apply successfully the differential rate in most establishments.
85. No system of management, however good, should be applied in a wooden way. The proper personal relations should always be maintained between the employers and men ; and even the prejudices of the workmen should be considered in dealing with ]them.
The employer who goes through his works with kid gloves on, and is never known to dirty his hands or clothes, and who either talks to his men in a condescending or patronizing way, or else not at all, has no chance whatever of ascertaining their real thoughts or feelings.
86. Above all it is desirable that men should be talked to on their own level by those who are over them.
Each man should be encouraged to discuss any trouble which he may have, either in the works or outside, with those over him. Men would far rather even be blamed by their bosses, especially if the “ tearing out ” has a touch of human nature and feeling in it, than to be passed by day after day without a word and with no more notice than if they were part of the machinery.
The opportunity which each man should have of airing his mind freely and having it out with his employers, is a safety-valve ; and if the superintendents are reasonable men, and listen to and treat with respect what their men have to say, there is absolutely no reason for labor unions and strikes.
87. It is not the large charities (however generous they may be) that are needed or appreciated by workmen, such as the founding of libraries and starting workingmen’s clubs, so much as small acts of personal kindness and sympathy, which establish a bond of friendly feeling between them and their employers.
Shop Management - Themes
Click on the link to read the theme in detail.
1.
Definition of Management
2.
Difference in Production Quantity between a first class man and an average man
3.
Developing and Employing First Class People in an Organization
4.
Confronting Soldiering - Slow Pace of Work
5.
Halsey Plan - F.W. Taylor's Comments
6.
Task Management
7.
Investment for Increasing Productivity or Efficiency
8.
Importance of people - organization
9.
Modern Engineering and Modern Shop Management
10.
Task Management - Starting and Ending Times
11.
Task Work - Some More Thoughts
12.
Usefulness of Gantt's system
13.
Time Study by F.W. Taylor
14.
Bicylcle Ball Inspection Case Study
15.
Need for Functional Foremanship or Functional Organisation of Foremen
16.
Functional Foremanship
17.
Production Planning and Control
18.
Role of Top Management in Managing Change to High Productive Shop
19.
Train Operators in High Productivity One by One and Then in Small Batches
20.
Organizing a Small Workshop for High Productivity
21.
Introducing Functional Foremanship
22.
Personal Relations Between Employers and Employed
23.
Don't be in a hurry - It Takes Time to Manage Change
24.
Best Practices in Shop Management
Important Points and Ideas in Shop Management - Abstracts
1. Definition of Management
The art of management has been defined, "as knowing exactly what you want men to do, and then seeing that they do it in the best and cheapest way.'"
What the workmen want from their employers beyond anything else is high wages, and what employers want from their workmen most of all is a low labor cost of manufacture.
These two conditions are not diametrically opposed to one another as would appear at first glance. On the contrary, they can be made to go together in all classes of work, without exception
This book is written mainly with the object of advocating high wages and low labor cost as the foundation of the best management, of pointing out the general principles which render it possible to maintain these conditions even under the most trying circumstances, and of indicating the various steps which the writer thinks should be taken in changing from a poor system to a better type of management.
The possibility of coupling high wages with a low labor cost rests mainly upon the enormous difference between the amount of work which a first-class man can do under favorable circumstances and the work which is actually done by the average man.
2. Difference in Production Quantity between a first class man and an average man
That there is a difference between the average and the first-class man is known to all employers, but that the first-class man can do in most cases from two to four times as much as is done by an average man is known to but few, and is fully realized only by those who have made a thorough and scientific study of the possibilities of men.
The difference in the output of first-class and average men is as little realized by the workmen as by their employers.
The second and equally interesting fact upon which the possibility of coupling high wages with low labor cost rests, is that first-class men are not only willing but glad to work at their maximum speed, providing they are paid from 30 to 100 per cent more than the average of their trade. Men will not work at their best unless assured a good liberal increase, which must be permanent.
3. Developing and Employing First Class People in an Organization
4. Confronting Soldiering - Slow Pace of Work
5. Halsey Plan - F.W. Taylor's Comments
6. Task Management
The writer has found, through an experience of thirty years, covering a large variety in manufactures, as well as in the building trades, structural and engineering work, that it is not only practicable but
comparatively easy to obtain, through a systematic and scientific time study, exact information as to how much of any given kind of work either a first-class or an average man can do in a day, and with this information as a foundation, he has over and over again seen the fact demonstrated that workmen of all classes are not only willing, but glad to give up all idea of soldiering, and devote all of their energies to turning out the maximum work possible, providing they are sure of a suitable permanent reward.
With accurate time knowledge as a basis, surprisingly large results can be obtained under any scheme of management from day work up; there is no question that even ordinary day work resting upon this foundation will give greater satisfaction than any of the systems in common use, standing as they do upon soldiering as a basis.
The writer chooses from among a large variety of trades to which these principles have been applied, the yard labor handling raw materials in the works of the Bethlehem Steel Company at South Bethlehem, Pa.,
The first step was to place an intelligent, college-educated man in charge of progress in this line. This man had not before handled this class of labor, although he understood managing workmen. He was not familiar with the methods pursued by the writer, but was soon taught the art of determining how much work a first-class man can do in a day. This was done by timing with a stop watch a first-class man while he was working fast. The best way to do this, in fact almost the only way in which the timing can be done with certainty, is to divide the man's work into its elements and time each element separately. For example, in the case of a man loading pig-iron on to a car, the elements should be: (a)
picking up the pig from the ground or pile (time in hundredths of a minute); (b) walking with it on a level (time per foot walked); (c) walking with it up an incline to car (time per foot walked); (d)
throwing the pig down (time in hundredths of a minute), or laying it on a pile (time in hundredths of a minute); (e) walking back empty to get a load (time per foot walked).
The most difficult elements to time and decide upon in this, as in most cases, are the percentage of the day required for rest, and the time to allow for accidental or unavoidable delays.
Example of 400% increase in work output
Between twelve and thirteen tons of pig-iron per man had been carried from a pile on the ground, up an inclined plank, and loaded on to a gondola car by the average pig-iron handler while working by the day.
A man was selected from persons doing this task to make the first start under the writer's system. He was trained in a new way of working as developed by Taylor and his associates and supervised. He loaded on piece work from forty-five to forty-eight tons (2,240 lbs. each) per day.
He regarded this task as an entirely fair one, and earned on an average, from the start, $1.85 per day, which was 60 per cent more than he had been paid by the day.
As the first man started on the work earned steadily $1.85 per day, this object lesson gradually wore out the opposition to the new arrangement, which ceased rather suddenly after about two months. From this time on there was no difficulty in getting plenty of good men who were anxious to start on piece work under the new method in various jobs, and the difficulty lay in making with sufficient rapidity the accurate time study of the elementary operations or "unit times" which forms the foundation of this kind of piece work.
Throughout the introduction of piece work, which was done after a thorough time study, for each new section of the work, one man only was put on each new job, until he had demonstrated that the task set was a fair one by earning an average of $1.85 per day. After a few sections of the work had been
started in this way, the complaint on the part of the better workmen was that they were not allowed to go on to piece work fast enough. It required about two years to transfer practically all of the yard labor from day to piece work. And the larger part of the transfer was made during the last six months of this time.
The study of "unit times" for the yard labor took practically the time of two trained men for two years. Throughout this time the day and piece workers were under entirely separate and distinct management. The original foremen continued to manage the day work, and day and piece workers were never allowed to work together. Gradually the day work gang was diminished and the piece workers were increased as one section of work after another was transformed from the former to the latter.
Two elements which were important to the success of this work should be noted:
First, on the morning following each day's work, each workman was given a slip of paper informing him in detail just how much work he had done the day before, and the amount he had earned. This enabled him to measure his performance against his earnings while the details were fresh in his mind. Without this there would have been great dissatisfaction among those who failed to climb up to the task asked of them, and many would have gradually fallen off in their performance.
Second, whenever it was practicable, each man's work was measured separately by itself.
What the writer wishes particularly to emphasize is that this whole system rests upon an accurate and scientific study of unit times, which is by far the most important element in scientific management. With it, greater and more permanent results can be attained even under ordinary day work or piece work than can be reached under any of the more elaborate systems without it.
For each job there is the quickest time in which it can be done by a first-class man. This time may be called the "quickest time," or the "standard time" for the job. Under all the ordinary systems, this
"quickest time" is more or less completely shrouded in mist. In most cases, however, the workman is nearer to it and sees it more clearly than the employer.
Under ordinary piece work the management watch every indication given them by the workmen as to what the "quickest time" is for each job, and endeavor continually to force the men toward this "standard time," while the workmen constantly use every effort to prevent this from being done
and to lead the management in the wrong direction. In spite of this conflict, however, the "standard time" is gradually approached.
With accurate time study as a basis, the "quickest time" for each job is at all times in plain sight of both employers and workmen, and is reached with accuracy, precision, and speed, both sides pulling hard in the same direction under the uniform simple and just agreement that whenever a first-class man works his best he will receive from 30 to 100 per cent more than the average of his trade.
7. Investment for Increasing Productivity or Efficiency
Before starting to make any changes in the organization of a company the following matters should be carefully considered: First, the importance of choosing the general type of management best suited to the particular case. Second, that in all cases money must be spent, and in many cases a great deal of money, before the changes are completed which result in lowering cost. Third, that it takes time to reach any result worth aiming at. Fourth, the importance of making changes in their proper order, and that unless the right steps are taken, and taken in their proper sequence, there is great danger from deterioration in the quality of the output and from serious troubles with the workmen, often
resulting in strikes.
It is not at all generally realized that whatever system may be used, --providing a business is complex in its nature--the building up of an efficient organization is necessarily slow and sometimes very expensive.
Almost all of the directors of manufacturing companies appreciate the economy of a thoroughly modern, up-to-date, and efficient plant, and are willing to pay for it. Very few of them, however, realize that the best organization, whatever its cost may be, is in many cases even more important than the plant; nor do they clearly realize that no kind of an efficient organization can be built up without spending money. The spending of money for good machinery appeals to them because they can see machines after they are bought; but putting money into anything so invisible, intangible, and to the average man so indefinite, as an organization seems almost like throwing it away.
8. Importance of people - organization
The writer feels that management is also destined to become more of an art, and that many of the, elements which are now believed to be outside the field of exact knowledge will soon be standardized tabulated, accepted, and used, as are now many of the elements of engineering. Management will be studied as an art and will rest upon well recognized, clearly defined, and fixed principles instead of depending upon more or less hazy ideas received from a limited observation of the few organizations with which the individual may have come in contact. There will, of course, be various successful types, and the application of the underlying principles must be modified to suit each particular case. The writer has already indicated that he thinks the first object in management is to unite high wages with a low labor cost. He believes that this object can be most easily attained by the application of the
following principles:
(a) A LARGE (specified) DAILY TASK. --Each man in the establishment, high or low, should daily have a clearly defined task laid out before him. This task should not in the least degree be vague nor indefinite, but should be circumscribed carefully and completely, and should not be easy to accomplish (unless the operator works for the full allotted time with adequate speed).
(b) STANDARD CONDITIONS. --Each man's task should call for a full day's work, and at the same time the workman should be given such standardized conditions and appliances as will enable him to accomplish his task with certainty.
(c) HIGH PAY FOR SUCCESS (in completing the task). -- He should be sure of large pay when he accomplishes his task.
(d) LOSS IN CASE OF FAILURE (to complete the task). --When he fails he should be sure that sooner or later he will be the loser by it (because of low wages).
When an establishment has reached an advanced state of organization, in many cases a fifth element should be added, namely: the task should be made so difficult that it can only be accomplished by a first-class man.
They call, however, for a greater departure from the ordinary types of organization than would at first appear. In the case, for instance, of a machine shop doing miscellaneous work, in order to assign daily to each man a carefully measured task, a special planning department is required to lay out all of the work at least one day ahead. All orders must be given to the men in detail in writing; and in order to lay out the next day's work and plan the entire progress of work through the shop, daily returns must be made by the men to the planning department in writing, showing just what has been done. Before
each casting or forging arrives in the shop the exact route which it is to take from machine to machine should be laid out. An instruction card for each operation must be written out stating in detail just how each operation on every piece of work is to be done and the time required to do it, the drawing number, any special tools, jigs, or appliances required, etc. Before the four principles above referred to can be successfully applied it is also necessary in most shops to make important physical changes. All of the small details in the shop, which are usually regarded as of little importance and are left to be regulated according to the individual taste of the workman, or, at best, of the foreman, must be thoroughly and carefully standardized; such. details, for instance, as the care and tightening of the belts; the exact shape and quality of each cutting tool; the establishment of a complete tool room from which properly ground tools, as well as jigs, templates, drawings, etc., are issued under a good check system, etc.; and as a matter of importance (in fact, as the foundation of scientific management) an accurate study of unit times must be made by one or more men connected with the planning department, and each machine tool must be standardized and a table or slide rule constructed for it showing how to run it to the best advantage.
At first view the running of a planning department, together with the other innovations, would appear to involve a large amount of additional work and expense, and the most natural question would be is whether the increased efficiency of the shop more than offsets this outlay? It must be borne in mind, however, that, with the exception of the study of unit times, there is hardly a single item of work done in the planning department which is not already being done in the shop. Establishing a planning department merely concentrates the planning and much other brainwork in a few men especially fitted for their task and trained in their especial lines, instead of having it done, as heretofore, in most
cases by high priced mechanics, well fitted to work at their trades, but poorly trained for work more or less clerical in its nature.
9. Modern Engineering and Modern Shop Management
There is a close analogy between the methods of modern engineering and the new type of management. Engineering now centers in the drafting room. Similarly, modern shop management's work now centers in the planning department.
10. Task Management - Starting and Ending Times
When men are working on task work by the day they should be made to start to work at the regular starting hour. They should, however, have no regular time for leaving. As soon as the task is finished they should be allowed to go home; and, on the other hand, they should be made to stay at work until their task is done, even if it lasts into the night, no deduction being made for shorter hours nor extra pay allowed for overtime.
11. Task Work - Some More Thoughts
12. Usefulness of Gantt's system
13. Time Study by F.W. Taylor
When work is to be repeated many times, the time study should be minute and exact. Each job should be carefully subdivided into its elementary operations, and each of these unit times should receive the most thorough time study. In fixing the times for the tasks, and the piece work rates on jobs of this class, the job should be subdivided into a number of divisions, and a separate time and price assigned to each division rather than to assign a single time and price for the whole job. This should be done for several reasons, the most important of which is that the average workman, in order to maintain a rapid pace, should be given the opportunity of measuring his performance against the task set him at frequent intervals. Many men are incapable of looking very far ahead, but if they see a definite opportunity of earning so many cents by working hard for so many minutes, they will avail
themselves of it.
14. Bicycle Ball Inspection Case Study
The work consisted briefly in placing a row of small polished steel balls on the back of the left hand, in the crease between two of the fingers pressed together, and while they were rolled over and over, with the aid of a magnet held in the right hand, they were minutely examined in a strong light, and the defective balls picked out and thrown into especial boxes. Four kinds of defects were looked for--dented, soft, scratched, and fire cracked--and they were mostly minute as to be invisible to an eye not especially trained to this work. It required the closest attention and concentration. The inspection girls had worked on day work for years, ten and one-half hours per day, with a Saturday half-holiday.
The first move before in any way stimulating them toward a larger output was to insure against a falling off in quality. This was accomplished through over-inspection. Every two or three days a lot of balls was especially prepared by the foreman, who counted out a definite number of perfect balls, and added a recorded number of defective balls of each kind. The inspectors had no means of distinguishing this lot from the regular commercial lots. The results inspection of those lots were compared with the known results.
After insuring in this way against deterioration in quality, effective means were at once adopted to increase the output. Improved day work was introduced. An accurate daily record, both as to quantity and quality, was kept for each inspector. In a comparatively short time this enabled the foreman to stir the ambition of all the inspectors by increasing the wages of those who turned out a large quantity and good quality, at the same time lowering the pay of those who fell short, and discharging others who proved to be incorrigibly slow or careless. An accurate time study was made through the use of a stop watch and record blanks, to determine how fast each kind of inspection should be done. This showed that the girls spent a considerable part of their time in partial idleness, talking and half working, or in actually doing nothing.
Talking while at work was stopped by seating them far apart. The hours of work were shortened from 10 1/2 per day, first to 9 1/2, and later to 8 1/2; a Saturday half holiday being given them even with the shorter hours. Two recesses of ten minutes each were given them, in the middle of the morning and afternoon, during which they were expected to leave their seats, and were allowed to talk.
The shorter hours and improved conditions made it possible for the girls to really work steadily. Piece work was then introduced, a differential rate being paid, not for an increase in output, but for greater accuracy in the inspection; the lots inspected by the over-inspectors forming the basis for the payment of the differential. The work of each girl was measured every hour, and they were all informed whether they were keeping up with their tasks, or how far they had fallen short and an assistant was sent by the foreman to encourage those who were falling behind, and help them to catch up.
The final results of the improved system in the inspecting department were as follows:
(a) Thirty-five girls did the work formerly done by one hundred and twenty.
(b) The girls averaged from $6.50 to $9.00 per week instead of $3.50 to $4.50, as formerly.
(c) They worked only 8 1/2 hours per day, with Saturday a half-holiday, while they had formerly worked 10 1/2 hours per day.
(d) An accurate comparison of the balls which were inspected under the old system of day work with those done under piece work, with over-inspection. It was found that the accuracy of inspection under piece work was one-third greater than that under day work.
To summarize: the same ten girls did on an average each day in September, on piece work, when only working 8 1/2 hours per day, 2.42 times as much, or nearly two and one-half times as much, in a day (not per hour, the increase per hour was of course much greater) as they had done when working on day work in March with a working day of 10 1/2 hours. They earned $6.50 to $9.00 per week on piece work, while they had only earned $3.50 to $4.50 on day work. The accuracy of inspection under piece work was one-third greater than under day work.
15. Need for Functional Foremanship or Functional Organisation of Foremen
In the writer's experience, almost all shops are under-officered. The foreman has too many duties to fulfill.
His duties may be briefly enumerated in the following way. He must lay out the work for the whole shop, see that each piece of work goes in the proper order to the right machine, and that the man at the machine knows just what is to be done and how he is to do it. He must see that the work is not slighted, and that it is done fast, and all the while he must look ahead a month or so, either to provide more men to do the work or more work for the men to do. He must constantly discipline the men and readjust their wages, and in addition to this must fix piece work prices and supervise the timekeeping. Hence, Taylor advocates functional foremanship.
16. Functional Foremanship
The following is a brief description of the duties of the four types of executive functional bosses which the writer has found it profitable to use in the active work of the shop: (1) gang bosses, (2) speed bosses, (3) inspectors, and (4) repair bosses.
The gang boss has charge of the preparation of all work up to the time that the piece is set in the machine. It is his duty to see that every man under him has at all times at least one piece of work ahead at his machine, with all the jigs, templates, drawings, driving mechanism, sling chains, etc., ready to go into his machine as soon as the piece he is actually working on is done. The gang boss must show his men how to set their work in their machines in the quickest time, and see that they
do it. He is responsible for the work being accurately and quickly set, and should be not only able but willing to pitch in himself and show the men how to set the work in record time.
The speed boss must see that the proper cutting tools are used for each piece of work, that the work is properly driven, that the cuts are started in the right part of the piece, and that the best speeds and
feeds and depth of cut are used. His work begins only after the piece is in the lathe or planer, and ends when the actual machining ends. The speed boss must not only advise his men how best to do this work, but he must see that they do it in the quickest time, and that they use the speeds and feeds and depth of cut as directed on the instruction card In many cases he is called upon to demonstrate that the work can be done in the specified time by doing it himself in the presence of his men.
The inspector is responsible for the quality of the work, and both the workmen and speed bosses must see that the work is all finished to suit him. This man can, of course, do his work best if he is a master of the art of finishing work both well and quickly.
The repair boss sees that each workman keeps his machine clean, free from rust and scratches, and that he oils and treats it properly, and that all of the standards established for the care and maintenance of the machines and their accessories are rigidly maintained, such as care of belts and shifters, cleanliness of floor around machines, and orderly piling and disposition of work.
The following is an outline of the duties of the four functional bosses who are located in the planning room, and who in their various functions represent the department in its connection with the men. The first three of these send their directions to and receive their returns from the men, mainly in writing. These four representatives of the planning department are, the (1) order of work and route clerk, (2) instruction card clerk, (3) time and cost clerk, and (4) shop disciplinarian.
Order of Work and Route Clerk. After the route clerk in the planning department has laid out the exact route which each piece of work is to travel through the shop from machine to machine in order that it may be finished at the time it is needed for assembling, and the work done in the most economical way, the order of work clerk daily writes lists instructing the workmen and also all of the executive shop bosses as to the exact order in which the work is to be done by each class of machines or men, and these lists constitute the chief means for directing the workmen in this particular function.
Instruction Card Clerks. The "instruction card," as its name indicates, is the chief means employed by the planning department for instructing both the executive bosses and the men in all of the details of their work. It tells them briefly the general and detail drawing to refer to, the piece number and the cost order number to charge the work to, the special jigs, fixtures, or tools to use, where to start each cut, the exact depth of each cut, and how many cuts to take, the speed and feed to be used for each cut, and the time within which each operation must be finished. It also informs them as to the piece rate, the differential rate, or the premium to be paid for completing the task within the specified time (according to the system employed); and further, when necessary, refers them by name to the man who will give them especial directions. This instruction card is filled in by one or more members of the planning department, according to the nature and complication of the instructions, and bears the same relation to the planning room that the drawing does to the drafting room. The man who sends it into the shop and who, in case difficulties are met with in carrying out the instructions, sees that the proper man sweeps these difficulties away, is called the instruction card foreman.
Time and Cost Clerk. This man sends to the men through the "time ticket" all the information they need for recording their time and the cost of the work, and secures proper returns from them. He refers these for entry to the cost and time record clerks in the planning room.
Shop Disciplinarian. In case of insubordination or impudence, repeated failure to do their duty, lateness or unexcused absence, the shop disciplinarian takes the workman or bosses in hand and applies the proper remedy. He sees that a complete record of each man's virtues and defects is kept. This man should also have much to do with readjusting the wages of the workmen. At the very least, he should invariably be consulted before any change is made. One of his important functions should be that of peace-maker.
17. Production Planning and Control
The following are the leading functions of the planning department:
(a) The complete analysis of all orders for machines or work taken by the company.
(b) Time study for all work done by hand throughout the works, including that done in setting the work in machines, and all bench, vise work and transportation, etc.
(c) Time study for all operations done by the various machines.
(d) The balance of all materials, raw materials, stores and finished parts, and the balance of the work ahead for each class of machines and workmen.
(e) The analysis of all inquiries for new work received in the sales department and promises for time of delivery.
(f) The cost of all items manufactured with complete expense analysis and complete monthly comparative cost and expense exhibits.
(g) The pay department.
(h) The mnemonic symbol system for identification of parts and for charges.
(i) Information bureau.
(j) Standards.
(k) Maintenance of system and plant, and use of the tickler.
(l) Messenger system and post office delivery.
(m) Employment bureau.
(n) Shop disciplinarian.
(o) A mutual accident insurance association.
(p) Rush order department.
(q) Improvement of system or plant.
18. Role of Top Management in Managing Change to High Productive Shop
Before starting to make any radical changes leading toward an improvement in the system of management, it is desirable, and for ultimate success in most cases necessary, that the directors and the important owners of an enterprise shall be made to understand, at least in a general way, what is involved in the change. They should be informed of the leading objects which the new system aims at, such, for instance, as rendering mutual the interests of employer and employee through "high wages and low labor cost," the gradual selection and development of a body of first class picked workmen who will work extra hard and receive extra high wages and be dealt with individually instead of in masses.
They should thoroughly understand that this can only be accomplished through the adoption of precise and exact methods, and having each smallest detail, both as to methods and appliances, carefully selected so as to be the best of its kind. They should understand the general philosophy of the system and should see that, as a whole, the system to be introduced must be in harmony with its few leading ideas,
They should be shown that it pays to employ an especial corps to introduce a new system just as it pays to employ especial designers and workmen to build a new plant; that, while a new system is being introduced, almost twice the number of foremen are required as are needed to run it after it is in; that all of this costs money, but that, unlike a new plant, returns begin to come in almost from the start from improved methods and appliances as they are introduced, and that in most cases the new system more than pays for itself as it goes along; that time, and a great deal of time, is involved in a radical change in management, and that in the case of a large works if they are incapable of looking ahead and patiently waiting for from two to four years, they had better leave things just as they are, since a change of system involves a change in the ideas, point of view and habits of many men with strong convictions and prejudices, and that this can only be brought about slowly and chiefly through a series of object lessons, each of which takes time, and through continued reasoning; and that for this reason, after deciding to adopt a given type, the necessary steps should be taken as fast as possible, one after another, for its introduction. The directors should be convinced that an increase m the proportion of non-producers to producers means increased economy and not red tape, providing the non-producers are kept busy at their respective functions.
They should be prepared to lose some of their valuable men who cannot stand the change and also for the continued indignant protest of many of their old and trusted employees who can see nothing but extravagance in the new ways and ruin ahead.
19. Train Operators in High Productivity One by One and Then in Small Batches
Organizing for Introducing New Methods and Functional Foremenship
Before taking any steps toward changing methods the manager should realize that at no time during the introduction of the system should any broad, sweeping changes be made which seriously affect a large number of the workmen. Throughout the early stages of organization each change made should affect one workman only, and after the single man affected has become used to the new order of things, then change one man after another from the old system to the new, slowly at first, and rapidly as public opinion in the shop swings around under the influence of proper object lessons. Throughout a considerable part of the time, then, there will be two distinct systems of management in operation in the same shop; and in many cases it is desirable to have the men working under the new system managed by an entirely different set of foremen, etc., from those under the old.
The first step, after deciding upon the type of organization, should be the selection of a competent man to take charge of the introduction of the new system. The manager should keep himself free as far as possible from all active part in the introduction of the new system. While changes are going on it will require his entire energies to see that there is no falling off in the efficiency of the old system and that the quality and quantity of the output is kept up.
The respective duties of the manager and the man in charge of improvement, and the limits of the authority of the latter should be clearly defined and agreed upon, always bearing in mind that responsibility should invariably be accompanied by its corresponding measure of authority.
The worst mistake that can be made is to refer to any part of the system as being "on trial." Once a given step is decided upon to implement based on various trials, all parties must be made to understand, that now they have to implement.In making changes in system the things that are given a
"fair trial" fail, while the things that "must go," go all right.
Where to begin is a perplexing and bewildering problem. Employees are in general suspicious of change.
The first changes should be such as to allay the suspicions of the men and convince them by actual contact that the reforms are after all rather harmless and are only such as will ultimately be of benefit
to all concerned. Such improvements then as directly affect the workmen least should be started first. At the same time it must be remembered that the whole operation is of necessity so slow that the new system should be started at as many points as possible, and constantly pushed as hard as possible. In the metal working plant which we are using for purposes of illustration a start can be made at once along all of the following lines:
First. The introduction of standards (standard conditions) throughout the works and office.
Second. The scientific study of unit times on several different kinds of work.
Third. A complete analysis of the pulling, feeding power and the proper speeding of the various machine tools throughout the place with a view of making a slide rule for properly running each machine.
Fourth. The work of establishing the system of time cards by means of which ultimately all of the desired information will be conveyed from the men to the planning room.
Fifth. Overhauling the stores issuing and receiving system so as to establish a complete running balance of materials.
Sixth. Ruling and printing the various blanks that will be required for shop returns and reports, time cards, instruction cards, expense sheets, cost sheets, pay sheet, and balance records; storeroom; tickler; and maintenance of standards, system, and plant, etc.; and starting such functions of the planning room as do not directly affect the men.
If the works is a large one, the man in charge of introducing the system should appoint a special assistant in charge of each of the above functions just as an engineer designing a new plant would start a number of draftsmen to work upon the various elements of construction.
Training Functional Foremen
The most important and difficult task of the organizer will be that of selecting and training the various functional foremen who are to lead and instruct the workmen, and his success will be measured principally by his ability to mold and reach these men. They cannot be found, they must be made. They must be instructed in their new functions largely, in the beginning at least, by the organizer himself; and this instruction, to be effective, should be mainly in actually doing the work. Explanation and theory Will go a little way, but actual doing is needed to carry conviction. To illustrate: For nearly two and one-half years in the large shop of the Bethlehem Steel Company, one speed boss after another was instructed in the art of cutting metals fast on a large motor-driven lathe which was especially fitted to run at any desired speed within a very wide range. The work done in this machine was entirely connected, either with the study of cutting tools or the instruction of speed bosses. It was most interesting to see these men, principally either former gang bosses or the best workmen, gradually change from their attitude of determined and positive opposition to that in most cases of enthusiasm for, and earnest support of, the new methods. It was actually running the lathe themselves according to the new method and under the most positive and definite orders that produced the effect. The writer himself ran the lathe and instructed the first few bosses. It required from three weeks to two months for each man.
Perhaps the most important part of the gang boss's and foreman's education lies in teaching them to promptly obey orders and instructions received not only from the superintendent or some official high in the company, but from any member of the planning room whose especial function it is to direct the rest of the works in his particular line; and it may be accepted as an unquestioned fact that no gang boss is fit to direct his men until after he has learned to promptly obey instructions received from any proper source, whether he likes his instructions and the instructor or not, and even although he may be convinced that he knows a much better way of doing the work. The first step is for each man to learn to obey the laws as they exist, and next, if the laws are wrong, to have them reformed in the proper way.
20. Organizing a Small Workshop for High Productivity
In starting to organize even a comparatively small shop, containing say from 75 to 100 men, it is best to begin by training in the full number of functional foremen, one for each function, since it must be
remembered that about two out of three of those who are taught this work either leave of their own accord or prove unsatisfactory; and in addition, while both the workmen and bosses are adjusting themselves to their new duties, there are needed fully twice the number of bosses as are required to carry on the work after it is fully systematized.
21. Introducing Functional Foremanship
The first of the functional foremen to be brought into actual contact with the men should be the inspector; and the whole system of inspection, with its proper safeguards, should be in smooth and
successful operation before any steps are taken toward stimulating the men to a larger output; otherwise an increase in quantity will probably be accompanied by a falling off in quality.
Next choose for the application of the two principal functional foremen, viz., the speed boss and the gang boss.
It is of the utmost importance that the first combined application of time study, slide rules, instruction cards, functional foremanship, and a premium for a large daily task should prove a success both for the workmen and for the company, and for this reason a simple class of work should be chosen for a start. The entire efforts of the new management should be centered on one point, and continue there until unqualified success has been attained.
When once this gain has been made, a peg should be put in which shall keep it from sliding back in the least; and it is here that the task idea with a time limit for each job will be found most useful.
22. Personal Relations Between Employers and Employed
"No system of management, however good, should be applied in a wooden way. The proper personal relations should always be maintained between the employers and men; and even the prejudices of the workmen should be considered in dealing with them.
"The opportunity which each man should have of airing his mind freely, and having it out with his employers, is a safety-valve; and if the superintendents are reasonable men, and listen to and treat with respect what their men have to say, there is absolutely no reason for labor unions and strikes.
"It is not the large charities (however generous they may be) that are needed or appreciated by workmen so much as small acts of personal kindness and sympathy, which establish a bond of friendly feeling between them and their employers.
"The moral effect of this system on the men is marked. The feeling that substantial justice is being done them renders them on the whole much more manly, straightforward, and truthful. They work more cheerfully, and are more obliging to one another and their employers.
23. Don't be in a hurry - It Takes Time to Manage Change
Time is an important factor in managing the change from current productivity to high productivity. If any one expects large results in six months or a year in a very large works he is looking for the impossible. If any one expects to convert union men to a higher rate of production, coupled with high wages, in six months or a year, he is expecting next to an impossibility. But if he is patient enough to wait for two or three years, he can go among almost any set of workmen in the country and get results.
24. Best Practices in Shop Management
Taylor gives the various companies in which good practices in shop management were developed and implemented.
The remarkable system for analyzing all of the work upon new machines as the drawings arrived from the drafting-room and of directing the movement and grouping of the various parts as they progressed through the shop, which was developed and used for several years by Mr. Wm. II.
Thorne, of Wm. Sellers & Co., of Philadelphia,
The employment bureau is an interesting management practice and forms an important element of the Western Electric Company in Chicago. The complete and effective system for managing the messenger boys was introduced by Mr. Almon Emrie while he was superintendent of the Ingersoll Sargent Drill Company, of Easton, Pa. The mnemonic system of order numbers was invented by Mr. Oberlin Smith and amplified by Mr. Henry R. Towne, of The Yale & Towne Company, of Stamford, Conn.; The system of inspection was introduced by Mr. Chas. D. Rogers in the works of the American Screw Company, at Providence, R. I. The many good points in the apprentice system were developed by Mr. Vauclain, of the Baldwin Locomotive Works, of Philadelphia.
The card system of shop returns invented and introduced as a complete system by Captain Henry Metcalfe, U. S. A., in the government shops of the Frankford Arsenal. It is another distinct advance in the art of management.
New Development
Updated on 30.7.2022, 13 July 2021
Pub 13 Feb 2017